Maytag Microwave Parts

This motor-stator assembly provides the stationary magnetic core for the appliance's drive motor, restoring magnetic coupling so the motor can generate torque. Useful when the motor hums, fails to spin, or produces intermittent movement. What it does:

• Forms the stationary magnetic field the rotor needs to turn, enabling normal motor operation
• Restores drive function when the motor hums without spinning or runs weakly
• Can resolve intermittent start/stop or reduced torque issues tied to the motor assembly
• Works as the matched stationary component for the corresponding motor/rotor

• Always disconnect power before inspecting or replacing motor components.
• Handle wiring and connectors carefully; match original terminals and routing.
• Some motors are sealed assemblies and may require partial disassembly.
• Test the appliance after installation to confirm proper operation and secure mounting.

This belt-drive is the replacement drive belt that turns the dryer drum so clothes tumble evenly during the cycle. It restores drum rotation when the original belt is worn, stretched, or broken. What it does:

• Wraps around the dryer drum and motor/idler assembly to transfer motor torque to the drum
• Restores normal drum rotation when the belt has failed or slipped
• Helps eliminate symptoms like a non-turning drum, rubbing or squealing noises, or intermittent tumbling
• Compatible with dryers that use a single continuous drum drive belt

• One (1) belt-drive

• Disconnect power (and gas supply for gas models) before servicing
• Access the dryer drum per your model's service instructions—usually from the front or rear—before removing the old belt
• Route the belt around the drum and idler/tensioner exactly as shown in the model's diagram; ensure proper tension and alignment
• If you encounter damaged pulleys, idler, or motor issues, inspect and replace those parts as needed

Secures internal components and keeps cabinet panels aligned. Replace if bracket is cracked, broken, or missing to restore proper fit and stability.

Front vent grille that covers the microwave vent opening and directs airflow. Replaces cracked, broken, or missing grilles to restore appearance.

Fix microwave overheating or won't heat issues with this thermostat temperature limiter. Regulates oven temperature and prevents overheating damage.

Microwave won't heat? A faulty capacitor often causes no heating or weak performance. This high-voltage capacitor restores full power. Moderate DIY.

Connects the turntable motor to the drive shaft in your microwave. Replace if cracked, broken, worn, or fused to the motor, preventing turntable rotation.

Microwave door handle that mounts on the exterior door panel. Replace if your handle is cracked, broken, or missing. Attaches to door with fasteners.

Replaces a cracked, broken, or worn microwave door handle. Restores a secure grip for safe opening and closing. Direct-fit replacement part.

This propeller is the small impeller that mounts to the dishwasher circulation pump to move wash water through the spray arms for effective cleaning. Replacing a worn or damaged propeller restores proper water flow and wash performance. What it does:

• Spins on the pump shaft to circulate wash water through the spray arms
• Restores normal water flow when a cracked or stripped propeller reduces circulation
• Helps resolve symptoms such as poor cleaning, weak spray, or inconsistent water movement
• Works with the pump motor; does not include the motor or pump housing

• Disconnect power and water supply before beginning any repair
• Access the pump assembly from the dishwasher base or cabinet front per your model service instructions
• Inspect the pump shaft and seal for wear; replace damaged components to prevent repeat failure
• Reassemble carefully and test operation

Replacement mounting screw secures exterior panels, trim, or internal components. Needed when original fastener is missing, stripped, or damaged.

Plastic support clip that holds the wire cooking rack in place inside your microwave convection oven. Replace if cracked, broken, or melted during use.

Replace your damaged or missing microwave control button. This push button installs on the control panel and is needed when the original is cracked, broken, or worn out.

Coupler assembly connects the motor to the turntable tray in your microwave. Replace if worn, cracked, or missing to restore proper turntable rotation.