Parts for Ge JE1550WY01: 01 - Section1 Parts

Replace your microwave's mica spacer and thermal cutoff when sparking or overheating occurs. Essential safety component. Verify fit with your model number.

This Supporter - mgt is a small mounting support that helps secure and stabilize the appliance assembly where it attaches. It reduces movement and keeps related components aligned for reliable operation. What it does:

• Provides structural support for the appliance assembly and helps hold parts in position
• Reduces rattling, vibration, and movement caused by loose or worn supports
• Helps maintain proper alignment of adjacent panels or components
• Can prevent further wear or damage resulting from a loose assembly

• Disconnect power to the appliance before starting any repair
• Remove any trim or panels that block access to the mounting location
• Typical installation requires basic hand tools (screwdriver, nut driver); keep fasteners organized

This microwave thermostat monitors the internal temperature and automatically shuts off the microwave when it reaches 105 degrees Celsius to prevent overheating. It protects your microwave from damage caused by excessive heat buildup. Replace this part if your microwave shuts off unexpectedly during normal operation or if it overheats frequently.

This power cord assembly provides the main electrical connection for the appliance, restoring safe, reliable power delivery when the original cord is damaged or fails. Designed to match the OEM connection type and fit. What it does:

• Delivers mains power from the wall outlet to the appliance's terminal block
• Replaces frayed, cut, or heat-damaged power cords that can cause loss of power
• Helps stop symptoms like the appliance not powering on, intermittent power, or visible cord damage
• Restores a proper grounding/neutral connection when the cord or terminals are compromised

• Always disconnect power at the breaker and verify the appliance is de-energized before servicing
• Secure the cord with the appliance's strain relief or clamp to prevent stress on the electrical terminals

Lower door hinge for microwaves. Secures the bottom of the door to the cabinet frame. Replace if cracked, broken, or causing door misalignment.

Microwave not heating but runs? Replace the magnetron to restore cooking power. Intermediate DIY repair taking 1-2 hours with proper safety steps.

Microwave not heating or humming loudly? The high-voltage diode converts AC to DC for the magnetron. Repair takes 30-45 minutes with basic tools.

The Microwave Door Switch is an OEM part for GE microwaves, designed to prevent the microwave from operating when the door is open by interrupting the power whenever the door is not securely closed. The door switch is an essential safety feature.

Symptoms of a failing Microwave Door Switch include:

• The microwave not starting or heating
• Running when the door is opened
• Unusual noises when the door is closed  

Causes of a bad Microwave Door Switch can result from repeated opening and closing of the door or slamming that can cause the switch to degrade or become misaligned, leading to intermittent or failure.

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This is a monitor or interlock switch that detects whether the microwave door is properly closed before allowing the unit to operate. It is a safety device that shuts off microwave power if the door is open or if other door switches malfunction. Replace this switch if the microwave does not start, runs with the door open, or blows a fuse when the door is closed.

This part has been discontinued and is no longer available.

This glass tray is a flat oven shelf that provides a smooth, easy-to-clean surface for baking and roasting. It restores a stable cooking surface and replaces cracked, chipped, or otherwise damaged oven glass trays. What it does:

• Supports bakeware and cookware for even heating on the oven floor or shelf area
• Replaces trays that are cracked, chipped, or shattered and may cause uneven cooking
• Provides a smooth, non-porous surface that's simple to wipe clean
• Helps prevent food drips from contacting the oven floor when used as intended

• One glass tray

• Handle carefully; glass can break and cause injury—wear cut-resistant gloves
• Allow the oven to cool completely before removing or installing the tray
• Inspect tray for chips or stress cracks before first use; do not use if damaged
• Follow the appliance manufacturer's instructions for placement and safe use

This is a humidity sensor mounted inside the microwave that detects moisture levels in the cooking cavity. It enables auto-cook and auto-reheat functions by signaling the control board when food has released enough steam. Replace this sensor if auto-cook cycles consistently overcook or undercook food, or if the microwave displays a sensor error code.

Fix a microwave that won't heat or has no power with this low voltage transformer. Common repair for dead displays and control panel issues.

This electronic control board manages all microwave operations including power levels, cooking time, and display functions. It processes user inputs and controls the magnetron and other components to provide proper microwave cooking performance. Replace when the microwave won't start, display shows error codes, or cooking power becomes inconsistent.

This inner door frame secures the oven's inner panel and helps support the inner glass, keeping the door assembly stable and aligned for safe, efficient oven operation. Replacing a damaged inner frame restores proper door fit and appearance. What it does:

• Supports and positions the inner door panel and inner glass
• Helps maintain proper door alignment and seal for efficient heating
• Prevents rattling or looseness caused by bent or cracked frames
• Restores safe, stable door operation and original fit

• Disconnect power to the appliance before starting any repair
• Handle glass and sharp edges carefully; wear gloves and eye protection
• Removal may require lifting out the door and removing retaining screws or clips

Replace your microwave's door hinge pin if the original is broken, bent, or missing. This small rod secures the door hinge assembly for smooth operation.

Microwave door screen that installs behind the glass to protect internal components. Replace if cracked, damaged, or showing rust spots or holes.