Parts for Frigidaire DB400A1: 06 - Motor Pump Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Replacement screw for dishwasher assembly and mounting. Used to secure components throughout your dishwasher. Replace if stripped, missing, or damaged.

Dishes not drying properly? Your dishwasher heating element may have failed. This element heats water and dries dishes during the final cycle. DIY fix.

Fix poor water spray and dishes not getting clean with this dishwasher wash impeller kit. Replaces worn or broken impellers with missing fins.

Replacement dishwasher filter chopper blade that grinds food particles in the sump assembly. Replace if dishes aren't cleaning well or you hear grinding noise. Verify fit by model number.

Seals the connection between your dishwasher pump and housing to prevent leaks. Replace when you notice water pooling or dripping. Confirm fit with your model.

This O-ring is a small rubber sealing gasket that prevents water leaks at a refrigerator water connection. It restores a watertight seal to stop drips and maintain proper water flow to the dispenser/ice system. What it does:

• Creates a watertight seal at a water line or valve connection
• Helps stop visible dripping or slow leaks from fittings
• Maintains proper pressure and flow by preventing bypass around a joint
• Used where a compressible seal is required between two mating parts

• Shut off water supply and disconnect power before servicing
• Replace only with the correct-size O-ring and seat it evenly in the groove
• Inspect mating surfaces for nicks or debris; clean before installing the new O-ring
• Tighten fittings to manufacturer torque recommendations to avoid over-compression

Dishwasher pump gasket seals the circulation pump to prevent leaks. Replace if you notice water pooling under the dishwasher. Verify fit with your model.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Replace your dishwasher pump housing if water isn't draining or you hear grinding noises. Moderately difficult repair requiring basic tools.

Replace your dishwasher's connector kit if the original is cracked, broken, or missing. This adapter installs between key components to ensure proper fit.

Watershield assembly for dishwashers. Protects internal components from water damage. Replace if cracked, warped, or missing to prevent leaks.

Motor mounting screw for dishwashers. Secures the motor assembly to the frame. Replace if missing, stripped, or damaged during motor service or repair.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

This washer heater assembly heats and maintains wash water temperature to improve detergent performance and cleaning for temperature-sensitive cycles. Designed as a direct replacement part for compatible top- and front-load machines. What it does:

• Heats incoming water to reach selected cycle temperatures for better soil removal.
• Helps maintain water temperature during the wash portion of the cycle.
• Common symptom: washer runs but water stays cold or loads are not cleaned as expected.
• Common symptom: water temperature error codes or washer fails temperature-sensitive cycles.

• Disconnect power and water supply before starting any repair.
• Handle the heating element and wiring with care; avoid damage to terminals and gasket surfaces.
• Installation may require removal of access panels and basic hand tools.
• After installation, restore power and run a short test cycle to check for leaks.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

This part has been discontinued by the manufacturer and is no longer available.

Protective shield that covers the dishwasher spray arm assembly. Replace this guard if it's cracked, broken, or missing to protect spray arm components.

This screw fastens the heater bracket to the appliance, providing a secure mount for the heating assembly. Replacing a worn or missing screw helps keep the bracket stable and maintains proper heater positioning. What it does:

• Secures the heater bracket to the cabinet or housing to hold the heating element in place
• Prevents bracket movement that can cause rubbing or vibration noises
• Reduces risk of intermittent heating caused by a loose heater assembly
• Helps maintain correct alignment of the heater and related components

• Disconnect power (and gas for gas models) before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Handle sharp sheet-metal edges carefully and follow all appliance safety instructions

The Side Mount Kit is an OEM replacement part for Frigidaire dishwashers. It contains mounting brackets, screws, and other hardware required to securely install the dishwasher against cabinetry in a side-by-side configuration. Proper attachment is necessary for stability and safety during operation. 

Symptoms of damaged or missing mounting hardware include:

• Excessive movement or rocking of the dishwasher body
• Potential detachment from cabinets  
• Screws pulling loose from repeated vibrations
• Improper door alignment causing difficulty closing fully

Causes related to normal wear over extended use periods. Damage may occur if weight is applied during improper lifting or installation attempts.  

Compatible models include Electrolux, Gibson, and select Kenmore units.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.