Mtd Gold Engine Parts

This is a recoil starter assembly, first designed for rototillers, but also used on some models of wood chippers. It measures 7 inches in diameter and has a metal housing rather than plastic. This makes it more durable, suitable for heavy-duty lawn care responsibilities. The pull cord itself is standard nylon, well suited to pulling a heavier recoil. The purpose of a recoil starter assembly is to provide a relatively low-impact way of starting the engine. Instead of turning a crank, an operator can pull a cord, which is housed inside the starter assembly. Under ordinary circumstances, this assembly will rarely need to be entirely replaced, but damage can occur due to dropping or due to pulling the cord too hard when the engine is seized. In this case, a recoil starter assembly is a drop-in repair. Unscrew the old starter assembly, seat the new one, and screw it in. This is an OEM part sourced directly from the manufacturer, and it is sold individually.

A cotter pin is a standard piece of hardware typically used on lawn and garden equipment as a method of securing something to an axle or round shaft. These pins are thin and, although they are durable, they can rust or become damaged over time. In some instances, they can break off or become lost in the process of other repairs. A replacement with the right size and style of cotter pin will ensure that equipment is in working order at all times. This genuine OEM cotter pin replacement can be used with select lawn and garden equipment from MTD, Huskee, Yard Man, Yard Machines, Troy-Bilt, Bolens, Cub Cadet, and Murray. It can be used on lawn tractors, log splitters, chipper/shredder units, and snowblowers. There are more than 150 compatible units, so owners should consult their parts diagram for application(s) of this pin. Note that this pin may have multiple applications on a single machine. This cotter pin is sold individually and may require needle nose pliers to replace.

The purpose of the fuel nipple in a small engine is to clean the fuel before it reaches the carburetor. If the fuel is dirty, it could cause issues with the carburetor and other parts of the engine. If the engine misfires, has a fuel odor, leaks, or has problems with dirty fuel getting into the carburetor, it may be time to replace the fuel nipple. It is an easy replacement, but be sure to work in a well-ventilated area. Drain the fuel tank and disconnect the spark plug before beginning this repair. This OEM fuel nipple is a genuine part right from the manufacturer. This fuel nipple can work well for snowblowers, snow throwers, chippers, tillers, and log splitters. It is compatible with a range of models from brands like Craftsman, Yard Machines, Yard-Man, MTD, and Troy-Bilt.

This is a replacement fuel bowl gasket that is specifically made for select models of snowblowers. The fuel bowl gasket is used to create a seal in the fuel bowl, allowing the carburetor to maintain appropriate pressure and deliver the fuel properly throughout the engine. Over time, gaskets like this one will become compressed and deteriorated, creating a leak in their seal. This can lead to fuel or air leakage, poor engine performance, and more serious damage if left unrepaired. Replacing gaskets is typically considered routine maintenance, and it is essential to replace them as quickly as possible. This genuine fuel bowl gasket is manufactured to OEM specifications by MTD and designed for use in select machines from MTD, as well as those from Cub Cadet, HUSKEE, Lawn Chief, RYOBI, Troy-Bilt, Craftsman, Remington, Yard Machines, Yard Man, and Bolens. There are hundreds of machines that can use this fuel bowl gasket. It is made of durable rubber material and sold as a single unit. Always be sure to inspect gaskets when performing other maintenance and repairs and use the correct tools for gasket replacement to prevent damage during installation.

This air cleaner cover is designed to house the air filter on larger lawn equipment and other outdoor power tools. There is no aspect of small engine care more necessary than protecting the air that goes into the carburetor and cylinder from yard dust. Nothing is more incapacitating to a small engine than being clogged with dust, pollen, and other particulates that are invariably stirred up during landscaping work. While the air cleaner cover itself is not a moving part and would not seem to be subject to replacement, it is occasionally the case that, through extensive use or accidental contact, the cover becomes unable to shield the air filter within it. In these cases, it is essential to replace the cover with an OEM certified replacement cover that has been manufactured to the same specification as the original. Though replacing the cover itself is quite simple, it probably a very good idea to replace the air filters at the same time. If the cover is in need of replacement, it is quite likely the filters have been exposed to excessive amounts of particulate. This cover can be used on chippers, shredders, log splitter, mowers, and a variety of other small engine/large job equipment. Compatible brands include Troy-Bilt, MTD, Yard-Man, Yard Machines, and Cub Cadet.

Here is a replacement fuel tank for use with a range of different models of small engines. The fuel tank plays one of the most important roles in a machine with an internal combustion engine. The tank holds the gas, which flows through the fuel line, so the machine can operate. Although fuel tanks are durable and built to last, there could be any number of reasons that one may need to be replaced. On older machines, for example, the fuel tank could have become damaged or corroded. Even newer machines could have a faulty fuel tank that would need to have a replacement. If there is an issue with the tank, it is not a replacement that can wait. The tank could be leaking fuel, for example, which can be wasteful as well as dangerous. This genuine OEM replacement fuel tank is identical to the one that came with the machine. It is sold individually and does not include any of the hardware needed for replacement. It can work with dozens of models of tillers, log splitters, and other small engines. Compatible brands include Troy-Bilt, Cub Cadet, MTD, HUSKEE, MasterCut, and Yard Machines.

A gas powered engine often requires priming before it can run, which means injecting some of the fuel into the engine's carburetor. Here, a careful balance of air and gas will receive a spark that causes combustion. The most common way to prime an engine is to use a primer assembly that is activated by a bulb that is pressed to create suction and draw fuel into a reservoir or carburetor. This replacement fuel bulb is for snowblowers that rely on gas powered engines to run. The fuel bulb is very flexible and made to endure seasonal conditions. It works with Craftsman, Yard Machines, MTD, Troy Bilt, and Bolens snowblowers. This is an OEM replacement part that fits into the cover assembly and which requires only a wrench to replace and install. It is sold individually, and other components of the priming assembly may be needed.

The fuel line is used to carry fuel through the machine, and it must be in good condition. As fuel line parts age, they are prone to damage. In some cases, they might crack, which could result in a fuel leak. Other times, the ends of the tube might not fit properly, even when they are clamped down. Eventually, the fuel line will need to be replaced. This is a relatively simple job, which will require only a pair of pliers to complete. This replacement fuel line kit is sold individually. This OEM kit will include the rubber tube as well as two metal clamps for attaching the line to the machine. The fuel line may be used with snowblowers, lawnmowers, tillers, leaf blowers, log splitters, wood chippers, and other small engines, It will work with machines from many different brands, including MTD, Yard Machines, Troy-Bilt, Yard-Man, Bolens, Cub Cadet, and Husky.

This flat washer is used to attach the idler pulley in a number of small and medium sized gasoline powered engines. These engines include snow blowers, log splitters, riding mowers, lawn tractors, and chippers. Because the idler pulley is subject to a great deal of resistance when the pulley is engaged, eventually the pulley will wear out. Should there be a squealing sound when engaging the drive, the problem is likely the idler pulley. In these cases, the pulley must be replaced. It is a good idea to replace the surrounding hardware when replacing the idler pulley; tNhis includes the flat washer, which is subject to corrosion during heavy use. To replace the idler pulley, first detach the spark plug cap. If on a mower or tractor, drop the mower deck. Remove the original pulley and install in order: replacement pulley, hex bolt, flat washer, flange nut. Apart from dropping the mower deck, the only tools required to complete this installation may be a 9/16 ratchet and combination wrench. This washer is a genuine OEM replacement part, designed to perfectly replicate the original piece. This washer is compatible with Troy-Bilt, Yard Man, Yard Machines, MTD, and Craftsman devices.

The hex lock nut is found on many different types of outdoor lawn equipment, as well as other types of equipment. The lock nut works to secure bolted joints by adding friction to the bolt threads. The nut has flat sides, which can easily be gripped by a wrench to be tightened or loosened as needed. These types of nuts are common, as they provide easy assembly and disassembly of various parts. Buyers may need a new hex lock nut for a range of reasons. The nut that is currently on the equipment could have become damaged or lost while working on the machine. It is vital for all of the nuts to be in place and properly secured on the equipment before use. This is an authentic OEM part. Some of the products that use hex lock nuts include lawn mowers, snowblowers, tillers, edgers, string trimmers, and log splitters. Common equipment brands using these nuts include Craftsman, Toro, Cub Cadet, Yard Machines, and Troy-Bilt.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.

This is a genuine replacement for the air cleaner thumb screw found on select engines used in lawn mowers. The thumb screw is a specialty part that is used to secure the air cleaner in a stable position. Over time, the screw can become damaged or worn because of the constant engine vibrations or exposure to high heat. This screw may also be lost during air filter replacements or other repair work. In either case, it should be replaced with a genuine part like this one to ensure the air cleaner remains secure and the machine can continue to be used. This genuine OEM thumb screw is manufactured by MTD and is compatible with several machines from the brand. It can also be used with models from Bolens, Yard Man, Yard Machines, HUSKEE, Cub Cadet, and Troy-Bilt. There are hundreds of compatible models that can use this thumb screw. The part is made of durable metal with a black plastic grip for easy installation with no tools required. This item is sold individually and does not include additional hardware or parts. Always allow the engine to cool completely and wear gloves when working on lawn and garden equipment.