Mtd Gold Lawn Mower Parts

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

This part is a replacement hex flange bearing. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a detached, defective, or damaged hex flange bearing in a variety of lawn tractor models. This part provides support for the lawn tractor shaft and also enables it to rotate without creating too much friction. This is a high wear and tear part and may require replacement with age or regular equipment use. A wrench set and screwdriver will be needed to replace this part. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this hex flange bearing, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this hex flange bearing is suitable for use on several different models of lawn tractors manufactured by MTD, Troy-Bilt, Yard Man, and Cub Cadet. This is a genuine part made of high-quality, durable metal and is sold individually.

The spacer is a standard piece of hardware that is used on various lawn mowers. This spacer has multiple applications based on the model and design. It is typically installed on shafts and in places where an additional gap is needed between connections or hardware. These parts are durable, but can become damaged or worn over time and require a replacement. Without functioning spacers, parts may rub together and create friction or simply fail to work properly. Replacing parts with genuine OEM hardware like these standard spacers will get the equipment back in working order. This genuine OEM spacer is designed for use with a number of mowers from MTD, Yard Machines, Troy-Bilt, Husky, Cub Cadet, and Yard Man. This spacer is made of durable metal and sold as a single unit. Those who need more than one will have to order multiple quantities. Always wear gloves when performing lawn mower repairs.

The muffler on lawnmowers prevents neighbors from becoming overly upset when the grass is cut early in the morning. When the engine starts on the lawnmower, the combustion releases burnt gas, making a very loud noise. The muffler dissipates the noise to make the lawnmower run more quietly. Over time, heat from the exhaust and constant exposure to the elements may cause the muffler to rust and possibly have holes that increase the noise. If this happens, the muffler should be removed and replaced to keep the noise to a minimum. Wait for the engine to cool so that the muffler is cool to the touch. Wear work gloves and have a socket set and adjustable wrench available. Remove the muffler screws and set them aside to use on the new muffler. Remove the damaged muffler from the mounting bracket. Install the new muffler on the mounting bracket using the mounting screws from the old muffler. Tighten the screws and start the lawnmower to ensure the muffler is installed correctly. This muffler is a silver metal part that is sold as one unit. It does not come with attachment screws. It is designed for use on lawn mowers manufactured by MTD, Ryobi, Yard Machines, Bolens, Yard Man, Troy-Bilt, and Husky.

This muffler is a genuine OEM replacement part sourced directly from the manufacturer for use on lawn and garden equipment. It reduces the noise coming from the exhaust. Being a metal part exposed to the elements, it is not uncommon for mufflers to corrode over time and need replacement. As a lawnmower part, the muffler may sustain damage from debris in the yard while mowing. In either case, the muffler should be removed and replaced to keep the noise level to a minimum.The engine and damaged muffler should be cool to the touch before repairing the lawnmower. Wear work gloves and safety goggles. Remove the spark plug from the lawnmower for extra safety. Locate the bolts securing the muffler to the lawnmower and loosen them to remove the muffler. Dispose of the old muffler and align the new muffler with the bolts. Attach the new muffler and tighten the nuts. Put the spark plug back in the lawnmower. This muffler is a high-quality metal part that is individually sold. It does not come with hardware. It is designed for use on lawn mowers and lawn tractors manufactured by MTD, Ryobi, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Poulan, and Husky.

This is a genuine replacement for the air cleaner thumb screw found on select engines used in lawn mowers. The thumb screw is a specialty part that is used to secure the air cleaner in a stable position. Over time, the screw can become damaged or worn because of the constant engine vibrations or exposure to high heat. This screw may also be lost during air filter replacements or other repair work. In either case, it should be replaced with a genuine part like this one to ensure the air cleaner remains secure and the machine can continue to be used. This genuine OEM thumb screw is manufactured by MTD and is compatible with several machines from the brand. It can also be used with models from Bolens, Yard Man, Yard Machines, HUSKEE, Cub Cadet, and Troy-Bilt. There are hundreds of compatible models that can use this thumb screw. The part is made of durable metal with a black plastic grip for easy installation with no tools required. This item is sold individually and does not include additional hardware or parts. Always allow the engine to cool completely and wear gloves when working on lawn and garden equipment.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

This air cleaner housing is a genuine MTD part, sold individually. This air cleaner housing can be used as a replacement part for lawn mowers and leaf blowers. The air cleaner housing provides a casing for the air cleaner so that it can shield the internal engine from dirt, debris, and pebbles. Check the air cleaner housing regularly to ensure that it is intact and no debris is getting into the engine. Remember to wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This air cleaner housing is compatible with the following brands: MTD, Huskee, and Yard-Man.

The ignition coil is a standard part of internal combustion engines on lawn and garden equipment. This coil consists of the ignition plug, plastic housing, and metal wires that include a flexible plastic casing. The coil is responsible for connecting the spark plug and transmitting the current that creates the spark that allows the engine to fire. This coil may develop wiring problems or the rubber and plastic parts may become worn and damaged over time. This will require a full replacement of the assembly. It is a good idea to inspect the coil when changing the spark plug as a part of routine maintenance, as well. This genuine OEM ignition coil is compatible with lawn and garden equipment from Troy-Bilt, MTD, Yard Machines, Yard Man, HUSKEE, and Cub Cadet. It can be used on more than 150 lawn and garden machines, including lawn mowers, log splitters, and chipper/shredder models. This coil assembly includes the ignition plug, metal wires encased in plastic, and a plastic housing. The hardware required to install this part is sold separately, as are all other components. Be sure to wear gloves and allow the engine to cool before working on the ignition or other components.