Mtd Pro Snow Removal Equipment Parts

This exhaust piping is a genuine OEM replacement part sourced directly from the manufacturer; it is used on tiller engines and other small engines. The exhaust piping is part of the muffler system. It connects to the exhaust manifold. As gas is combusted to run the engine, it is forced out through the exhaust manifold and the exhaust piping. This process heats the pipes for a short period. Over a period of time, this repeated heating can cause the exhaust piping to deteriorate. If this happens, the piping will need to be replaced in order for the exhaust manifold to function correctly. If the engine is experiencing overheating problems, the exhaust pipes will need to be replaced when it is fixed. Overheating will cause them to deteriorate much faster than normal.Allow the engine and exhaust manifold to cool before replacing the exhaust piping. Remove the exhaust pipes from the exhaust manifold. Inspect the manifold for visible signs of damage while the pipes are off. This would be a good time to replace the exhaust manifold gasket. Install the new pipes. The exhaust piping is made of durable black plastic and sold as an individual unit. It is compatible with tillers, chipper shredders, snowblowers, and other small engines manufactured by Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This fuel tank assembly can be used as a replacement part for the small engine of a snowblower or a tiller. The fuel tank assembly contains the fuel tank as well as the parts required to install the part. The purpose of the fuel tank is to store fuel for the engine and dispense the fuel in order to power the engine.A fuel tank assembly might be ordered as a complete replacement part if the fuel tank and its components suffer damage. This damage might manifest in the form of fuel leakages from punctures, holes, or corrosion to the material. If this damage affects the fuel tank and its components, it should be removed and replaced before using the appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This fuel tank assembly is compatible with the following brands: MTD, Troy-Bilt, Yard Man, and Cub Cadet.

This part is a replacement friction wheel assembly. It is intended to replace a defective or broken friction wheel assembly in snow blowers.The friction wheel works with the friction disc to turn the drive wheel axle. This part is essential to proper equipment functionality but may be damaged with regular equipment usage. Before beginning this repair job, disconnect spark plug. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before beginning. This friction wheel assembly is a genuine MTD OEM part made of durable materials and is sold individually. It is suitable for use with snow blower models that have been manufactured by MTD, Craftsman, Troy-Bilt, and some other brands.

This grease plug is a genuine OEM replacement part sourced directly from the manufacturer. It is found on snowblowers and other outdoor yard machines on the gearcase assembly, which houses the auger gear. The grease plug seals the oil port on the gearbox. This keeps lubrication inside the gearbox and is the access point for adding more when needed. If this plug is lost, the gearbox's oil could leak out, and contaminants could get into the gearbox.Lubricate the contents of the gearbox before installing the new grease plug. Locate and remove the two screws on the side to drain the gearbox. Install the grease plug in the bottom. Refill the oil using the vent hole. Continue filling until oil is coming out the top side screw. Close everything back up, and the machine is ready for use. To prepare the equipment for long storage, remove the grease plug and check the oil level. If it is not to the top, add more lubricant before sealing the grease plug.This grease plug is made of durable black molded plastic and is sold as an individual unit. It is compatible with snowblowers and snow throwers manufactured by Ryobi, MTD, Yard Machines, Troy-Bilt, Bolens, Yard-Man, Cub Cadet, and Husky.

This genuine MTD replacement part is a rocker arm for use with snowblowers, lawn tractors, and other equipment with an engine. A properly functioning rocker arm is essential for the safe and reliable use of the equipment. The rocker arm works to open the intake and exhaust valves. The rocker arm may become worn out or damaged with extended use, necessitating replacement. Remember to check the rocker arm periodically to spot any wear or damage. This part is an identical replacement for a rocker arm that is missing, worn out, or damaged. Prior to working with this part, please refer to the original product manual for a full list of included parts and installation instructions. A wrench set may be required for installation of this part. For safety, always wear gloves and ensure unit is powered down and cool prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and it is sold individually. It is made of high-quality durable metal. This part is compatible with a variety of MTD, Yard Machines, Troy-Bilt, Yard Man, Cub Cadet, Husky, and other equipment. Please note: original part numbers 1843974, 751-11966 is now obsolete, and manufacturer has replaced the original part numbers with this part.