Mtd Pro Snow Removal Equipment Parts

This shave plate is a genuine MTD part, sold individually. This shave plate can be used as a replacement part in a snowblower. The purpose of the shave plate in a snowblower is to unpack densely packed blocks of ice and snow as the snowblower is in use.The shave plate in a snowblower might suffer damage that can warrant a full replacement of the component. This could occur if the shave plate has been dented, punctured, cracked, chipped, warped, eroded, or otherwise damaged. If this occurs, the shave plate should be removed and replaced by this genuine OEM replacement part in order to continue safe usage of the snowblower.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This shave plate is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Yard Machines, Huskee, and Yard Man.

This replacement clutch drive is a part of the drive system and wheel assembly on snowblowers. The clutch drive engages the transmission when the engine is turned on so that the snowblower auger will rotate as the machine is pushed forward. This part is subject to repetitive motion and constant use so it sometimes just wears down with regular use. If something gets into the snowblower auger or other areas, that could damage the clutch drive, as well. In the event there is damage or the clutch drive no longer works as it should, it will need to be replaced with an OEM part like this one. This is a genuine replacement part made to OEM standards. It can be used in compatible machines from MTD, Craftsman, Troy-Bilt, and Yard-Man. The clutch drive is sold individually. It will not contain any additional parts or components. Disconnect the power supply or disengage the engine before working on outdoor power equipment. Allow the unit to cool and be cautious working around the auger as the blades can be quite sharp.

This snow thrower frame cover is an authentic OEM replacement part sourced directly from the manufacturer for use on snow throwers to protect the drive system from debris and dirt while removing snow. If the snow thrower's frame cover is damaged or broken, the machine should not be used until it is replaced. During regularly scheduled inspections and at the start of each snow season, the snow thrower should be inspected for damage. If the snow thrower frame cover is damaged, replace it with this new part.Before replacing parts on the snow thrower, make sure the key is not in the ignition and that the spark plug is not in the machine. Remove any fuel in the machine so that doesn't leak when the machine is turned on its edge. Park the snow thrower on a flat surface and pivot it forward so that it is now resting on the auger housing. Locate the screws holding the thrower frame cover in place and remove them. Set them aside to use on the new snow thrower. Remove the damaged framed cover and replace it with the new one. Reinstall the screws and tighten. Refill the gas and reinstall the spark plug.This thrower frame is a red metal part that is sold individually. It does not come with the screws used to secure it. This thrower frame cover is designed for use on snow throwers manufactured by Husky, Yard Machines, MTD, Troy-Bilt, and Yard-Man.

This listing is for an MTD rod support bracket. This part is designed for installation on various brands of snowblower and snow thrower machines. This rod support bracket is designed to provide strength and durability to the chute of a snowblower. The piece attaches to the frame of the machine on one end and the chute on the other end. The support bracket is fastened by a bolt on each end. By providing enhanced durability to the chute, this support bracket ensures the chute doesn't become weak and break due to vibration or high levels of movement. Begin installation by removing the old bracket with a nut driver. Remove the bolts fastening the old support bracket to the chute and frame of the machine. Replace the bolts after lining up the new rod support bracket. Do not overtighten the bolts or strip the head of the bolts when installing the new part.This support bracket is sourced directly from MTD as a genuine OEM replacement part. Only the rod support bracket is included with this listing. This part is compatible with MTD, Troy Bilt, Yard Machines, MTD, and Yard-Man brand snowblowers.

This lower chute is a genuine MTD part, sold individually. This lower chute can be used as a replacement part in a snowblower. The purpose of the lower chute in a snowblower is to allow the dispensing of snow out of the way of the operator and out of the side or back of the snowblower while the appliance is in operation. The lower chute in a snowblower might have to be replaced if the snow can no longer be properly channeled through and then out of the chute while the snowblower is being driven across a snowy surface. If the lower chute is punctured, scraped, dented, cracked, warped, eroded, or otherwise damaged to the point that snow is clogged within it, cannot pass through it, or falls out of it while the snowblower is in use, the lower chute should be removed and replaced by this genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This lower chute is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Yard Machines, Huskee, and Yard Man.

This replacement part is a plug kit. This is a genuine replacement part made by MTD. Plug kits are a great tool that allows the user to repair punctured tires or wheels in different kinds of lawn mowers or other machinery. A new plug kit might be needed if the current one is no longer working properly. If the part no longer works to assist the user in filing tires or repairing a wheel, it would be a good idea to replace this part. Always make sure that the engine is powered down before attempting to repair a tire. Work gloves are also recommended in this situation. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This genuine replacement part is an air filter heating cover for snowblowers. The air filter heating pipe cover is the plastic piece that covers the heating pipe of a snowblower. This cover is meant to protect the user from burning themselves on the heating pipe while using the machine. If the heating pipe cover is damaged to the point where it is no longer covering the heating pipe, it should be replaced. Thankfully, replacing this part is a simple process.To replace the heating pipe cover, locate the mounting screws that secure it to the snowblower. Before removing, make sure the engine has cooled to avoid getting burned. Once located, remove the mounting screws that attach the cover. Once removed, replace with the new cover and fasten the screws tightly. This OEM replacement part is sold individually and is compatible with MTD brand snowblowers.

This part is an ignition coil assembly. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, detached, or broken ignition coil on certain outdoor power equipment models. Ignition coils are essential for transforming battery voltage into an electrical spark to ignite fuel and start the engine. Over time and with regular usage, ignition coils can easily become worn out and affect the performance of outdoor power equipment. Signs of a failing ignition coil include engine misfires, inability to start equipment, and rough idling. Please be aware that proper tools are needed to replace this part and correct safety measures should always be followed when working on any type of equipment. For the most accurate information on installing this replacement ignition coil, specific manufacturer diagrams should always be referenced.As an authentic replacement part, this ignition coil assembly can be used on multiple different models of Craftsman, Cub Cadet, Troy-Bilt, MTD, and Husky snow blowers. Please note that this ignition coil assembly is a genuine part made of high-quality materials and is sold individually.

This replacement part is a cylinder head assembly. The cylinder head assembly covers the engine head cylinder and houses the cylinder valves. Over time, the cylinder head assembly can become damaged due to excessive wear and tear. If the engine is no longer running as efficiently as it once did, the cylinder head assembly might need to be replaced. Luckily, this is a fairly simple repair.Before beginning, make sure the engine of the mower has cooled. Once cool, begin by lifting up the hood or engine cover and detach it. Remove the air filter cover. Lift out the air filter. Using a three-eighths socket or wrench remove the blower housing mounting bolts. Detach the oil drain tube and lift off the blower housing. Unthread the bolts that secure the intake manifold and detach the breather tube. Set the carburetor assembly aside. Then unthread the spark plug. Remove the mounting bracket and unthread the exhaust manifold bolts. Pull the manifold free of the muffler. Unthread the valve cover mounting bolts. Pry the cover off with a putty knife and be prepared for some oil to spill. Once the cover is off use the three-eights inch socket wrench to remove the old cylinder head mounting bolts. Pull the old cylinder assembly out of its place and replace it with the new assembly.This genuine OEM part is compatible with MTD brand lawnmowers.

This replacement part is a flywheel. This is a genuine replacement part made by MTD. This part is a large rotating piece, similar to a wheel, that provides the engine with rotational energy that is later converted to other types of energy so that the engine can operate smoothly. A new flywheel might be needed if the current one is missing or damaged. If the user hears unusual noises coming from inside the engine area, the flywheel might be out of place and not working properly. If this is the case, it might be best to replace this part. Be sure the engine is completely powered down and cooled off before repairing this part. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This carburetor gasket is located between the insulator and the carburetor, creating a strong seal between the two to allow for optimal compression and engine performance. Over time and due to constant heat exposure, gaskets can degrade or become damaged. This can result in leaks in the system, which will impact performance and could cause the engine to fail completely if not properly addressed. If the carburetor gasket becomes faulty in any capacity, it needs to be replaced as soon as possible. This genuine OEM gasket replacement is manufactured to exact standards and is compatible with several models of snowblower engines from Troy-Bilt, MTD, Yard Man, Yard Machines, Cub Cadet, and Husky. This gasket is made of durable material, but gaskets could be more prone to damage or breakage during other repairs, so always use caution when working with this part. Allow the engine to cool completely and wear gloves when performing any engine repairs for hand protection.

This part is a replacement muffler shield. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. It is intended to replace a defective or broken muffler shield in snow blowers.The muffler shield protects the muffler and also ensures that the user is protected, as the muffler can become hot during equipment usage. This part will need to be replaced if detached, cracked, or in any way rendered ineffective. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this muffler shield, the appropriate owner's manual and equipment diagrams should be referred to. This muffler shield is a genuine OEM part made of durable materials and is sold individually. It is suitable for use with snow blower models that have been manufactured by MTD, Craftsman, Troy-Bilt, and other brands.