Mtd Snow Removal Equipment Parts

Flange bearing for lawn tractors and walk-behind mowers. Replace if you notice excessive noise, vibration, or wheel wobble. Verify fit with your model number.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

A ball bearing is a rolling element bearing that uses balls to maintain the separation between the bearing races. This part is designed for use with outdoor lawn and garden power equipment such as snowblowers, chippers, shredders, and tillers. It is compatible with products by brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, and MasterCut.The ball bearing part is crucial because its purpose is to reduce rotational friction while supporting radial and axial loads. Without functioning ball bearings, valuable outdoor equipment would fall apart and quickly stop working. That is why it is important to get any ball bearings replaced if they are worn out or malfunctioning.This ball bearing is made out of metal. The ball bearing is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

Replace your snow thrower's drive control cable if it's frayed, broken, or disconnected. This cable connects the drive control lever to the transmission.

Replacement auger clutch control cable for gas snowblowers. Connects handlebar control lever to auger engagement mechanism. Needed when frayed or broken.

Clutch control cable for gas snowblowers. Connects the clutch lever to the drive mechanism. Replace if cable is frayed, stretched, broken, or detached.

Replacement drive control cable for gas snowblowers. Installs from handle to drive system. Replace if cable is frayed, broken, stretched, or seized.

Control cable that operates the chute lock mechanism on your snowblower. Connects chute lock to control lever. Replace if cable is frayed, broken, or stretched.

Control cable that connects the handle lever to the auger clutch mechanism on gas snowblowers. Replace if cable is frayed, snapped, or stretched.

Drive control cable for snowblowers. Connects drive control handle to engine mechanism. Replace if cable is frayed, broken, kinked, or detached.

This is a throttle body intended for use with lawnmowers and tractors. The throttle body is attached to the control cable, the throttle control wire, and the throttle lever. It can be damaged or wear out with regular use. Signs that the throttle body is failing or going bad include a very low idle or poor idle. Stalling of the machine when stopping the device is another indicator that the throttle body is bad. When this happens, a new throttle body must be installed.Replacing a throttle body is simple. It requires a set of pliers, a wrench, and a screwdriver. Always wear gloves when working on a throttle body repair. Make sure to allow time for the machine to cool completely before beginning the repair.This throttle bottle is an authentic OEM part. It is supplied directly from the manufacturer. The throttle body is made of high-quality, durable plastic material. It is sold as an individual unit. The throttle body is compatible with Huskee, MTD, Yard Machines, Yard-Man, and Cub Cadet brands. It can be installed in various machines, including push-behind lawn mowers, lawn tractors, and other lawn equipment."

Replacement clutch cable that connects the control lever to the drive clutch on your snow thrower. Needed when the original cable is frayed, broken, or worn.

Steering control cable for gas snowblowers. Connects steering mechanism to handlebars. Replace if cable is frayed, broken, kinked, or disconnected.

Fixes snow blower drive issues caused by worn or damaged adapter pulley. Restores proper belt tension and transmission engagement for smooth operation.

Snowblower won't start or shuts off unexpectedly? This ignition switch controls engine power. Direct replacement part restores reliable starting.