Parts for Ge GFE28GYNJFS: Optional Accessories Parts

This coupler is a small connector used in refrigerators to join two mating parts within an assembly. Replacing a worn or damaged coupler restores a secure connection and reliable operation at that joint.

• Connects and secures two mating components within the appliance
• Helps transfer motion or maintain a sealed connection, depending on the application
• Common symptoms include a loose/slipping connection, unusual noise, or leaks at the joint
• Replace if cracked, stripped, or no longer holding securely

• Disconnect power; if working on the water system, also shut off the household water supply
• Note the original orientation/positions before removal for accurate reassembly
• Seat parts fully; for push-in connections, insert straight and perform a light tug test to engagement
• Restore power (and water, if applicable), then test operation and inspect the joint for leaks or slippage

The Icemaker Fill Tube Heater is an OEM component specifically designed for GE refrigerators. Located near the icemaker assembly, this heating element plays a crucial supporting role.

Symptoms of a bad fill tube heater include:

• Irregular or inconsistent ice production amounts  
• Cracked, cloudy or malformed ice cubes being generated
• The icemaker failing to operate or stop working altogether
• Water or moisture around the refrigerator icemaker area 

Causes can include wear over time from powering on during each ice-making cycle. Mineral deposits may also form and insulate the heating surface, reducing effectiveness.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This is a replacement round-head screw sized 10-24 x 5/8 in. It secures trim, panels, and internal components so parts stay aligned and appliances run quietly and safely. What it does

• Fastens panels, brackets, and trim pieces in place
• Prevents loose parts that can rattle or cause misalignment
• Replaces missing or stripped screws to restore secure mounting
• Works where a 10-24 x 5/8 round-head screw is required

• Disconnect power before servicing the appliance
• Use the proper screwdriver or nut driver to avoid stripping the head
• Align parts before tightening and thread gently to avoid cross-threading
• Do not over-tighten; stop when snug to prevent panel distortion

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This PEX water line provides a flexible, durable water supply connection for compatible appliances, restoring proper water delivery for dispensers and ice makers. It resists kinking and corrosion for reliable flow. What it does:

• Carries potable water from the household supply to the appliance water valve or dispenser.
• Restores water flow when the original line is cracked, pinholed, or damaged.
• Helps prevent leaks compared with brittle or corroded rigid tubing.
• Supports normal dispenser and ice maker operation when installed correctly.

• One PEX water line.

• Turn off and disconnect the water supply and power before starting work.
• Drain remaining water from the line and fittings to avoid spills.
• Use the correct fittings and follow manufacturer torque recommendations; hand-tighten then final snug with wrench.
• After installation, slowly restore water, check all connections for leaks, and test dispenser/ice maker operation.

A small rubber grommet that cushions and seals the freezer liner, helping reduce vibration and prevent wear where components meet the inner cabinet. Replaces a worn or missing grommet to restore a snug fit and quieter operation. What it does

• Cushions the freezer liner and components to reduce rattling and vibration.
• Helps maintain a tight seal at the liner mounting point to limit movement and wear.
• Prevents direct metal-to-metal contact that can cause chipping or cracking of the liner.
• Commonly replaced when the liner is loose, noisy, or damaged around mounting points.

• Designed for direct replacement; remove power before accessing the freezer interior.
• Access may require removing shelves, drawers, or the liner trim; handle liner edges carefully.
• Inspect surrounding clips and fasteners; replace any damaged hardware to ensure proper fit.

The Icemaker is an OEM component specifically designed for GE refrigerators. Located within the freezer compartment, the icemaker automatically produces batches of ice for convenient access.

Causes of a bad icemaker can include wear and tear of mechanical parts from years of producing ice. Mineral buildup may also clog components and impact performance over time.

Symptoms of a bad icemaker include:

• Failure to produce ice or very slow production  
• Ice cubes joining together in clumps or odd shapes
• Loud grinding sounds emanating from the assembly
• Leaks or water drips detected around the unit

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This housing wire is the replacement wiring housing used with the ice maker assembly in the freezer compartment. It protects and routes ice-maker wiring to help maintain reliable ice production and prevent wire chafing. What it does

• Protects and organizes ice maker wiring inside the freezer to prevent damage and shorts
• Helps maintain a secure connection between the ice maker and freezer harness
• Commonly replaced when wiring housing is cracked, torn, or allowing wire exposure
• Can resolve intermittent ice maker operation or electrical arcing caused by damaged wire insulation

• One housing wire assembly as shown

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access may require removing the ice maker or freezer liner
• Handle wiring and connectors carefully to avoid damage; replace any worn connectors or clips

The Icemaker Fill Cup is an OEM replacement part for GE refrigerators responsible for directing the water flow into the icemaker, allowing for the creation of ice cubes. It securely attaches to the icemaker, preventing any leaks or spills that could disrupt the ice production.  

A bad fill cup can occur due to several factors. Common causes include cracks, damage, or wear and tear over time. If you notice symptoms such as leaks around the icemaker, improper ice production, or water overflow, it may indicate a need to replace the fill cup.

Symptoms of a bad fill cup include:

• Leaks around the icemaker area
• Insufficient or inconsistent ice production
• Water overflow or spills

Restore your refrigerator's ice-making capabilities by replacing the faulty fill cup with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This refrigerator ice bucket assembly stores the ice made by your icemaker and delivers it when needed. Replacing a cracked or worn bin restores smooth ice storage and consistent ice delivery performance. What it does:

• Collects and holds ice in the freezer/ice compartment
• Interfaces with the drive/auger on dispenser-equipped models to move ice out of the bin
• Helps maintain proper ice flow and reduce jams or clumping
• Common symptoms: cracked/broken bin, bin won't seat or lock, ice not dispensing or intermittent dispense

• Includes 1 ice bucket assembly

• Unplug the refrigerator before servicing; work with dry hands
• Empty and remove the old bucket; retain any screws/clips used by your model
• Transfer any reusable parts from the old bin if required by your model
• Slide the new bin in fully so it seats and engages the drive; restore power and test after fresh ice is produced

The Valve Double Im Asm is an OEM part for GE refrigerators. It houses two inlet water valves for the ice maker and water dispenser. 

Causes of failure can include mineral buildup or scale deposits obstructing the valve pathways over many years of use. General wear and tear on the internal valve mechanisms from continuous operation can also take a toll.

Symptoms of a faulty assembly include things like:

• Not dispensing water
• Reduced ice production or incomplete cubes
• Water not entering the ice maker
• Ice that is clumped or has hollow areas

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.