Parts for Electrolux E30MO65GSSC: 02 - Oven, Cabinet Parts

Microwave not heating or won't start? This monitor switch and fuse assembly controls power safety circuits. Moderate DIY repair for most models.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

Fix a microwave that won't heat or start with this thermal cutout fuse. This safety component prevents overheating. Takes 30-45 minutes to install.

This thermal cut-out is a temperature-sensing safety device that helps protect the refrigerator's defrost/heater circuit by opening the circuit when temperatures exceed safe levels. It prevents overheating and helps maintain normal defrost cycles. What it does:

• Senses temperature in the defrost/heater area and opens the circuit to stop heating if temperatures get too high
• Prevents overheating of defrost heater or related components
• Can cause defrost failure symptoms when faulty, such as excessive frost buildup or poor cooling
• May also contribute to long run-times or irregular defrost cycles when not operating correctly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the part and wiring gently; ensure correct orientation and secure connections per service manual
• Use the exact replacement part number for compatibility

Replacement light bulb for microwaves. Illuminates the interior and cooktop area. Replace when burned out or dim. Confirm fit with your model number.

This evaporator fan motor circulates cold air across the evaporator coil to keep the refrigerator and freezer compartments cold and balanced. Replacing a failing fan restores proper airflow and helps maintain set temperatures. What it does:

• Spins the evaporator fan blade to move air over the evaporator coil for even cooling
• Helps prevent ice build-up from poor airflow and uneven compartment temperatures
• Commonly needed when you hear a loud humming, rattling, or no airflow from the fridge section
• Supports defrost system performance by ensuring warm air is not trapped near the coil

• One evaporator fan motor

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing the evaporator cover inside the freezer compartment
• Handle wiring and connector clips carefully; ensure correct orientation of the fan blade before reassembly

Microwave not heating? This high voltage transformer powers the magnetron to generate heat. Critical component requiring careful installation.

Microwave won't heat or makes humming noise? This capacitor works with the magnetron to generate heat. Moderate difficulty repair, 30-45 minutes.

Microwave won't heat food? A failed diode prevents the magnetron from generating heat. This repair requires moderate skill and takes 30-45 minutes.

Microwave not heating food? The magnetron generates the microwaves needed for cooking. This repair requires electrical expertise and safety precautions.

Turntable stops rotating or turns briefly then stops? This motor restores rotation in microwaves. Requires bottom panel access and unit removal.

Microwave door won't close or latch properly? This door latch hook secures the door and restores normal closing. Simple DIY fix in under 15 minutes.

Support bracket for built-in microwaves and wall ovens. Installs inside the cavity to provide structural reinforcement. Replace if bent, cracked, or missing.

Replace your microwave's support plate if cracked, broken, or missing. This structural component mounts inside the cavity to support internal parts.

This complete door assembly replaces a damaged or worn door to restore sealing, alignment, and normal operation. It provides a ready-to-install replacement that helps stop air leaks and improves temperature control and usability. What it does:

• Replaces the appliance door structure so it opens, closes, and latches correctly
• Restores the door sealing surface to prevent air and moisture infiltration
• Helps resolve symptoms like poor temperature control, frost buildup, or visible door damage
• Eliminates rattling or misalignment caused by bent or broken door components

• Disconnect power (and water, if applicable) before beginning repair
• This assembly can be heavy or awkward—have a helper available for safe handling
• Align and secure mounting points per OEM instructions; test latch and seal before finishing
• If gasket or trim appears damaged, replace those components for optimal performance

Connects the turntable motor to the rotating glass tray in your microwave. Replace if the coupler is cracked, broken, or missing and the tray won't rotate.

Access panel cover that protects internal microwave components. Replace if cracked, broken, or missing to restore finished appearance and prevent dust entry.

Support plate for microwave ovens. Mounts inside the cavity to provide structural support. Replace if cracked, warped, or missing to restore stability.

Replacement rack assembly for microwave ovens. Installs inside the cavity to support cookware. Replace if bent, rusted, warped, or broken from heavy use.

This replacement information label displays factory markings and safety/rating information so your appliance remains properly identified and serviceable. It restores legible identification and compliance markings to the cabinet. What it does:

• Replaces a torn, faded, or missing information/nameplate label
• Restores printed factory markings such as manufacturing and safety/rating text
• Helps service technicians identify the unit and ratings during repair
• Prevents confusion from illegible or absent identification details

• One replacement information label

• Clean and dry the mounting surface; remove any grease or residue before applying
• Align the label carefully, then press firmly from one side to the other to ensure adhesion
• For best results, install at room temperature on a flat, non-porous surface
• No special tools required; avoid sharp objects that could scratch the label or appliance

This replacement identification decal restores legible equipment labeling so model, rating and safety information are visible for service and ownership. It helps replace faded, torn or peeling labels to improve readability and compliance. What it does:

• Provides a clear, adhesive identification decal with printed model/rating/safety information
• Replaces faded, torn or peeling factory labels that are hard to read
• Helps owners identify the appliance correctly during service
• Maintains visible safety and rating information required for repair or inspection

• Clean and dry the installation surface thoroughly before applying
• Peel backing and press decal firmly, smoothing out air bubbles for full adhesion
• Do not stretch, reposition repeatedly, or apply to wet/oily surfaces
• If label covers a vent or operational opening, confirm placement with service manual

This is a replacement adhesive identification label used to restore factory markings and safety information on the appliance. It helps keep model, rating or warning information legible for service and safe operation. What it does

• Replaces a torn, faded, or missing appliance identification label
• Restores readable model, serial, rating or warning information that owners rely on
• Helps prevent confusion during service by keeping factory markings visible
• Maintains appliance appearance and compliance with original labeling

• One adhesive identification label

• Clean and dry the application area before installing to ensure proper adhesion
• Align the label carefully and press firmly from one side to the other to avoid bubbles
• No specialized tools required; avoid stretching or folding the label during placement

This adhesive appliance label replaces a worn or missing identification/warning sticker so important model, safety or operating information remains visible. Keeps service and safety info readable for owners. What it does

• Replaces faded or damaged identification, rating or warning graphics on the appliance
• Restores legible safety and operating information that helps prevent misuse
• Helps confirm appliance details during troubleshooting and repairs
• Adhesive backing sticks to clean, flat surfaces for a long-lasting replacement

• Clean and dry the mounting surface; remove oils, dust and loose residue before applying
• Peel backing and press the label firmly in place, smoothing out air bubbles
• Replace only on compatible surfaces and locations; do not stretch or fold the label
• If removing old adhesive, use a plastic scraper and a mild solvent in a well-ventilated area; disconnect power to any nearby electrical components before working

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a replacement mounting screw used to fasten appliance panels, trim, or components. It restores secure attachment and helps eliminate rattling, loose parts, or misaligned panels for a clean, stable fit. What it does:

• Secures panels, brackets, or trim to the appliance chassis
• Stops vibration-related rattles and movement from loose fasteners
• Keeps components aligned for proper operation and appearance
• Replaces lost or stripped screws to restore factory fit

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and do not overtighten; stop when snug to avoid damage
• Inspect surrounding parts and replace as needed

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This replacement angle is a small metal mounting bracket used to secure components in place on compatible Frigidaire appliances. It restores proper positioning and support for panels or assemblies that rely on a fixed bracket. What it does

• Provides a sturdy mounting point to hold panels, rails, or small assemblies in alignment.
• Replaces bent, cracked, or missing brackets that allow shifting or vibration.
• Helps stop rattling, misalignment, or loose panels caused by a damaged bracket.
• Works as a direct-fit hardware piece when the original bracket is worn or broken.

• Installer should turn off power to the appliance and unplug before starting work.
• Use appropriate hand tools; bracket fasteners may require small screws or bolts.
• Keep track of removed fasteners and any shims or spacers—reinstall in the same order.

Replace your microwave door gasket to restore a proper seal and prevent heat loss. Fixes worn or damaged seals for consistent heating. Verify fit.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.