Parts for Electrolux E30MO75HPSC: 02 - Oven,Cabinet Parts

Microwave won't start or keeps running with door open? This door switch detects when the door closes, ensuring safe operation and proper functionality.

Microwave runs but won't heat, or stays on when door opens? A faulty door switch is the likely cause. DIY repair takes about 30 minutes with basic tools.

Microwave not defrosting properly? This thermal cut-out defrost thermostat monitors temperature to prevent overheating and maintain safe defrost cycles.

Replacement interior light bulb for microwave cavities. Replace when dim, flickering, or burned out to restore visibility. Confirm fit with your model.

Replace your microwave's light socket if bulbs fail to illuminate despite having power. Restores interior or under-cabinet lighting. Verify fit by model.

This evaporator fan motor circulates cold air across the evaporator coil to keep the refrigerator and freezer compartments cold and balanced. Replacing a failing fan restores proper airflow and helps maintain set temperatures. What it does:

• Spins the evaporator fan blade to move air over the evaporator coil for even cooling
• Helps prevent ice build-up from poor airflow and uneven compartment temperatures
• Commonly needed when you hear a loud humming, rattling, or no airflow from the fridge section
• Supports defrost system performance by ensuring warm air is not trapped near the coil

• One evaporator fan motor

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing the evaporator cover inside the freezer compartment
• Handle wiring and connector clips carefully; ensure correct orientation of the fan blade before reassembly

Microwave not heating? This high voltage transformer powers the magnetron to generate heat. Critical component requiring careful installation.

Microwave won't heat or makes humming noise? This capacitor works with the magnetron to generate heat. Moderate difficulty repair, 30-45 minutes.

Microwave not heating? The high voltage diode converts AC to DC for the magnetron. Common failure part when food stays cold. Moderate skill repair.

Microwave not heating food? The magnetron generates the microwaves needed for cooking. This repair requires electrical expertise and safety precautions.

Turntable stops rotating or turns briefly then stops? This motor restores rotation in microwaves. Requires bottom panel access and unit removal.

Door hinge for microwaves and wall ovens. Replaces worn, broken, or damaged hinges that prevent proper door alignment and smooth operation.

Replacement door hinge for microwaves and wall ovens. Installs on the door frame to support smooth opening and closing. Needed when hinge is broken or worn.

Replacement door latch hook for microwaves. Secures the door latch assembly to keep the door properly closed. Needed when the hook is broken or worn.

Microwave door won't stay closed? This door latch hook securely holds the door shut during operation. Mounts to the top interior of the door cavity.

Fixes microwave turntable that won't rotate or makes grinding noises. This cam guides the turntable rotation mechanism. Simple 10-minute repair.

Microwave door won't latch or close properly? This door cam guides the latch mechanism for secure closure. Common fix for alignment issues.

Support bracket for built-in microwaves and wall ovens. Installs inside the cavity to provide structural reinforcement. Replace if bent, cracked, or missing.

Connects the turntable motor to the rotating glass tray in your microwave. Replace if the coupler is cracked, broken, or missing and the tray won't rotate.

Access panel cover that protects internal microwave components. Replace if cracked, broken, or missing to restore finished appearance and prevent dust entry.

Waveguide cover for your microwave. Installs inside the cavity to protect internal components. Replace if cracked, burned, or missing. Fits various models.

This louvres assembly directs and controls air flow inside the freezer/refrigerator compartment to help maintain even cooling and circulation. It replaces worn or broken vent louvers to restore proper airflow routing. What it does:

• Channels cold air between compartments to support consistent temperature distribution.
• Replaces cracked, loose, or damaged louvers that can cause poor air circulation.
• Helps reduce hot spots and uneven cooling when functioning correctly.
• Fits behind interior panels and works with the existing duct/vent system.

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Remove interior panels or shelves as needed to access the vent; keep track of fasteners.
• Handle plastic louvers carefully to avoid cracking; align tabs and clips when seating the part.

This metal angle support bracket secures appliance panels and components to the cabinet, helping maintain alignment and stability for long-lasting operation. Use it to replace a bent, cracked, or missing bracket that lets panels shift or rattle. What it does

• Provides a stable mounting point for panels, housings, or internal components
• Restores proper alignment when a corner or panel sits uneven or gaps appear
• Reduces vibration and rattling caused by loose or damaged supports
• Helps prevent further wear from components rubbing or shifting out of place

• Disconnect power to the appliance before starting any repair
• Use the existing fasteners when possible; replace stripped or damaged screws
• Verify correct orientation and alignment before fully tightening fasteners
• Take care to avoid damaging seals or wiring

This replacement angle is a small metal mounting bracket used to secure components in place on compatible Frigidaire appliances. It restores proper positioning and support for panels or assemblies that rely on a fixed bracket. What it does

• Provides a sturdy mounting point to hold panels, rails, or small assemblies in alignment.
• Replaces bent, cracked, or missing brackets that allow shifting or vibration.
• Helps stop rattling, misalignment, or loose panels caused by a damaged bracket.
• Works as a direct-fit hardware piece when the original bracket is worn or broken.

• Installer should turn off power to the appliance and unplug before starting work.
• Use appropriate hand tools; bracket fasteners may require small screws or bolts.
• Keep track of removed fasteners and any shims or spacers—reinstall in the same order.

Spring component for microwave ovens. Installs internally to provide tension or support. Replace if spring is broken, stretched, or missing for proper function.

Spring component for microwave door mechanism. Replaces worn, broken, or missing springs that affect door operation. Structural part for door assembly.

Replace your microwave's support plate if cracked, broken, or missing. This structural component mounts inside the cavity to support internal parts.

This complete door assembly replaces a damaged or worn door to restore sealing, alignment, and normal operation. It provides a ready-to-install replacement that helps stop air leaks and improves temperature control and usability. What it does:

• Replaces the appliance door structure so it opens, closes, and latches correctly
• Restores the door sealing surface to prevent air and moisture infiltration
• Helps resolve symptoms like poor temperature control, frost buildup, or visible door damage
• Eliminates rattling or misalignment caused by bent or broken door components

• Disconnect power (and water, if applicable) before beginning repair
• This assembly can be heavy or awkward—have a helper available for safe handling
• Align and secure mounting points per OEM instructions; test latch and seal before finishing
• If gasket or trim appears damaged, replace those components for optimal performance

Support plate for microwave ovens. Mounts inside the cavity to provide structural support. Replace if cracked, warped, or missing to restore stability.

Label for built-in microwaves and wall oven combos. Replace worn, faded, or missing labels to restore appliance appearance and model information display.

This replacement adhesive label restores the appliance's original product and rating information so owners can identify model and serial details. It helps keep safety and specification markings legible for troubleshooting and repairs. What it does:

• Replaces a missing, torn, or faded product/rating label so model and serial info remain readable
• Preserves appliance specifications and safety markings used during service and part ordering
• Helps technicians confirm correct parts and diagnostics without guesswork
• Prevents misidentification that can delay repairs or lead to incorrect parts

• One adhesive product/rating label

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully; press firmly from one side to the other to avoid air bubbles
• Use gloves if handling adhesive-backed labels to avoid fingerprints or oils
• Do not stretch or trim the label; replace with the exact part supplied

This printed information label displays the appliance model, serial, electrical ratings and key manufacturing data so technicians and owners can identify the unit and specifications quickly and accurately. What it does:

• Shows model and serial numbers, voltage, and manufacturing details for identification
• Helps replacement parts and service information
• Assists technicians during diagnostics and maintenance
• Supports safe power and connection checks by showing rated electrical info

• Clean and dry the mounting surface before applying the label for best adhesion
• Peel backing and press firmly; avoid stretching or wrinkling during placement
• Replace only with the exact OEM label to preserve accurate unit information

This replacement appliance label provides the factory identification and safety information fastened to the appliance so you can read model/serial and safety/warning text clearly. It restores legible markings for servicing and ownership records. What it does

• Shows the appliance identification, model/serial or rating area and factory safety/warning text so technicians and owners can service data.
• Helps ensure required safety and operating instructions remain visible and readable.
• Replaces a torn, faded, or missing label that can make identification and troubleshooting harder.
• Supports accurate parts ordering and service by restoring the original markings.

• One replacement label

• Peel-and-stick replacement; clean and dry the surface thoroughly before applying.
• Align carefully and press from one edge to the other to avoid bubbles; firm pressure ensures adhesion.
• Do not stretch or trim the label unless explicitly specified by the equipment instructions.
• For safety, disconnect power or follow manufacturer safety precautions before working near electrical components.

Replacement mounting screw for microwave ovens. Secures internal components and panels. Needed when original screws are stripped, missing, or damaged.

Replacement mounting screw for microwave panels, brackets, and trim. Needed when original fastener is missing, stripped, or damaged during repair work.

Screw secures the door latch and upper hinge plate on your microwave. Replace if missing, stripped, or loose to properly fasten door hinges and latch.

This is a replacement mounting screw used to fasten appliance panels, trim, or components. It restores secure attachment and helps eliminate rattling, loose parts, or misaligned panels for a clean, stable fit. What it does:

• Secures panels, brackets, or trim to the appliance chassis
• Stops vibration-related rattles and movement from loose fasteners
• Keeps components aligned for proper operation and appearance
• Replaces lost or stripped screws to restore factory fit

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and do not overtighten; stop when snug to avoid damage
• Inspect surrounding parts and replace as needed

Replacement lever for microwave door or latch mechanisms. Installs to operate control arms and moving parts. Needed when original is cracked, broken, or worn.

Mounting bracket for built-in microwave ovens. Secures microwave chassis to cabinet or wall. Replace if bent, broken, or missing during installation.

Replace your microwave door gasket to restore a proper seal and prevent heat loss. Fixes worn or damaged seals for consistent heating. Verify fit.

Replacement trim panel for built-in microwaves. Installs around the outer frame to cover gaps and provide a finished look. Order when cracked or damaged.

Replacement trim panel for built-in microwaves. Covers the outer frame edge for a finished look. Order if your existing trim is cracked or missing.

This holder is a small mounting bracket that secures internal appliance components to prevent movement and maintain proper alignment, helping reduce noise and keep parts functioning reliably. What it does:

• Secures and positions an internal component or assembly to the appliance frame
• Prevents shifting or sagging that can cause rattling or misalignment
• Helps maintain proper spacing for connected parts to operate correctly
• Reduces noise caused by loose fittings or vibration

• Recommended for users comfortable with appliance repair; disconnect power before servicing
• Remove adjacent panels or components as needed for access; keep fasteners organized
• Inspect mating surfaces and replace any damaged screws or clips for a secure fit

This electronic power control board routes and regulates electrical power to the appliance's control components, restoring proper power and control when the original board fails. Use when the unit has lost power or shows erratic control behavior. What it does:

• Supplies and distributes power to the appliance's control circuits and user interface
• Replaces a damaged or failed control board that causes no power, intermittent operation, or unresponsive controls
• Restores normal control signals to relays, motors, and sensors when functioning correctly
• Helps resolve symptoms like flickering displays, failure to start, or random shutdowns

• One electronic power control board (PCB)

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Handle the board by its edges and avoid touching components or connector pins to prevent ESD damage
• Verify connectors and wire harness positions match before reconnecting; do not force connectors

Fix a microwave that won't heat or start with this thermal cutout fuse. This safety component prevents overheating. Takes 30-45 minutes to install.

Installation tool for mounting built-in microwave ovens. Required for proper alignment during install. Replace if missing, damaged, or worn from use.

This installation tool assists with mounting and securing your microwave during setup. Replace if lost, damaged, or missing from your original kit.

Mounting screw for microwave installations. Secures cabinet or wall mounting brackets. Replace if missing, stripped, or damaged during reinstallation.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.