Parts for Electrolux E30MO75HSSA: 03 - Oven, Cabinet Parts

Microwave not heating or won't start? This monitor switch and fuse assembly controls power safety circuits. Moderate DIY repair for most models.

This noise filter reduces electromagnetic interference generated by the microwave's electronics, preventing it from affecting other nearby appliances or electronic devices. It is typically located near the power input inside the microwave cabinet. Replace this filter if the microwave causes static on radios or TVs, trips breakers intermittently, or if the filter shows visible signs of burning or damage.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

Fix a microwave that won't heat or start with this thermal cutout fuse. This safety component prevents overheating. Takes 30-45 minutes to install.

This is a thermal cut-out safety device that shuts off the microwave when internal temperatures exceed safe operating limits. It functions as a protective thermostat to prevent overheating and potential damage to the appliance. Replace this part if the microwave shuts off unexpectedly during use, fails to power on, or if the unit is overheating.

This is a replacement light bulb for the interior cavity of a microwave oven. It illuminates the cooking area so you can monitor food while it heats. Replace this bulb if the interior light no longer turns on when the door is opened or during operation, and you have confirmed the bulb socket and wiring are functioning properly.

Replace your microwave's light socket if bulbs fail to illuminate despite having power. Restores interior or under-cabinet lighting. Verify fit by model.

This evaporator fan motor circulates cold air across the evaporator coil to keep the refrigerator and freezer compartments cold and balanced. Replacing a failing fan restores proper airflow and helps maintain set temperatures. What it does:

• Spins the evaporator fan blade to move air over the evaporator coil for even cooling
• Helps prevent ice build-up from poor airflow and uneven compartment temperatures
• Commonly needed when you hear a loud humming, rattling, or no airflow from the fridge section
• Supports defrost system performance by ensuring warm air is not trapped near the coil

• One evaporator fan motor

• Disconnect power to the appliance before starting any repair
• Typically accessed by removing the evaporator cover inside the freezer compartment
• Handle wiring and connector clips carefully; ensure correct orientation of the fan blade before reassembly

Microwave not heating? This high voltage transformer powers the magnetron to generate heat. Critical component requiring careful installation.

Microwave won't heat or makes humming noise? This capacitor works with the magnetron to generate heat. Moderate difficulty repair, 30-45 minutes.

Microwave won't heat food? A failed diode prevents the magnetron from generating heat. This repair requires moderate skill and takes 30-45 minutes.

If your microwave isn't heating food or heats unevenly, the magnetron may have failed. This high-voltage tube generates microwave energy for cooking.

Turntable stops rotating or turns briefly then stops? This motor restores rotation in microwaves. Requires bottom panel access and unit removal.

Microwave not heating? A failed transformer prevents the magnetron from generating heat. This high-voltage component requires electrical expertise to install.

This is a door hinge for a microwave oven that allows the door to pivot open and closed. It supports the weight of the door and ensures it seals properly against the frame when shut. Replace this hinge if the microwave door sags, does not close evenly, or if the hinge is visibly bent or broken.

This is the right-side door hinge for a microwave oven. It connects the door to the microwave frame and allows it to open and close smoothly while maintaining a secure seal. Replace this hinge if the microwave door is sagging, not closing properly, or if the hinge is visibly bent or broken.

Replacement door latch hook for microwaves. Secures the door latch assembly to keep the door properly closed. Needed when the hook is broken or worn.

The Latch is an OEM replacement part for Frigidaire built-in microwaves. Securely mounted to the top interior section of the microwave cavity door, the positive-locking latch holds the door safely shut during operation. Crafted from corrosion-resistant materials for extended use, the latch handle withdraws the hook mechanism with a simple pull to conveniently access food within.

Symptoms of a bad latch include:

• The microwave door popping or falling open unexpectedly  
• Difficulty closing or fully engaging the secure latch hook 
• Wear signs like loose mounting points or a worn handle

Causes can involve repeated opening/closing cycles gradually loosening mounting fixtures, or parts rendered ineffective by moisture intrusion over time.

Replacing this Frigidaire OEM latch prevents potential microwave door opening during cooking cycles. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore built-in models.

Replacement rotating cam actuator for microwave mechanisms. Installs in latch or linkage assemblies. Needed when original cam is worn, broken, or stripped.

This replacement cam is the small pivot piece that helps a refrigerator door hinge open and close smoothly and keep the door aligned. Installing the cam restores proper hinge movement for a secure, even door fit. What it does:

• Acts as the hinge pivot point to guide door rotation and alignment
• Helps prevent door sagging, binding, or uneven gaps
• Reduces noisy or rough hinge movement caused by a worn cam
• Works with the hinge assembly to maintain proper door sealing

• One cam

• Disconnect power to the appliance or unplug before starting any work
• Support the door while removing hinge fasteners to prevent damage or injury
• Inspect mating hinge surfaces and replace any damaged hardware for best results
• Tighten hinge fasteners to manufacturer torque and check door alignment after installation

Connects the turntable motor to the rotating glass tray in your microwave. Replace if the coupler is cracked, broken, or missing and the tray won't rotate.

Access panel cover that protects internal microwave components. Replace if cracked, broken, or missing to restore finished appearance and prevent dust entry.

This metal angle support bracket secures appliance panels and components to the cabinet, helping maintain alignment and stability for long-lasting operation. Use it to replace a bent, cracked, or missing bracket that lets panels shift or rattle. What it does

• Provides a stable mounting point for panels, housings, or internal components
• Restores proper alignment when a corner or panel sits uneven or gaps appear
• Reduces vibration and rattling caused by loose or damaged supports
• Helps prevent further wear from components rubbing or shifting out of place

• Disconnect power to the appliance before starting any repair
• Use the existing fasteners when possible; replace stripped or damaged screws
• Verify correct orientation and alignment before fully tightening fasteners
• Take care to avoid damaging seals or wiring

This replacement angle is a small metal mounting bracket used to secure components in place on compatible Frigidaire appliances. It restores proper positioning and support for panels or assemblies that rely on a fixed bracket. What it does

• Provides a sturdy mounting point to hold panels, rails, or small assemblies in alignment.
• Replaces bent, cracked, or missing brackets that allow shifting or vibration.
• Helps stop rattling, misalignment, or loose panels caused by a damaged bracket.
• Works as a direct-fit hardware piece when the original bracket is worn or broken.

• Installer should turn off power to the appliance and unplug before starting work.
• Use appropriate hand tools; bracket fasteners may require small screws or bolts.
• Keep track of removed fasteners and any shims or spacers—reinstall in the same order.

Replacement door spring for ovens and wall ovens. Restores proper door balance and controlled movement. Needed when original is broken, stretched, or missing.

Replace your microwave's support plate if cracked, broken, or missing. This structural component mounts inside the cavity to support internal parts.

This complete door assembly replaces a damaged or worn door to restore sealing, alignment, and normal operation. It provides a ready-to-install replacement that helps stop air leaks and improves temperature control and usability. What it does:

• Replaces the appliance door structure so it opens, closes, and latches correctly
• Restores the door sealing surface to prevent air and moisture infiltration
• Helps resolve symptoms like poor temperature control, frost buildup, or visible door damage
• Eliminates rattling or misalignment caused by bent or broken door components

• Disconnect power (and water, if applicable) before beginning repair
• This assembly can be heavy or awkward—have a helper available for safe handling
• Align and secure mounting points per OEM instructions; test latch and seal before finishing
• If gasket or trim appears damaged, replace those components for optimal performance

Support plate for microwave ovens. Mounts inside the cavity to provide structural support. Replace if cracked, warped, or missing to restore stability.

This replacement adhesive label restores the appliance's original product and rating information so owners can identify model and serial details. It helps keep safety and specification markings legible for troubleshooting and repairs. What it does:

• Replaces a missing, torn, or faded product/rating label so model and serial info remain readable
• Preserves appliance specifications and safety markings used during service and part ordering
• Helps technicians confirm correct parts and diagnostics without guesswork
• Prevents misidentification that can delay repairs or lead to incorrect parts

• One adhesive product/rating label

• Clean and dry the mounting surface before applying; remove old adhesive residue
• Align carefully; press firmly from one side to the other to avoid air bubbles
• Use gloves if handling adhesive-backed labels to avoid fingerprints or oils
• Do not stretch or trim the label; replace with the exact part supplied

This printed information label displays the appliance model, serial, electrical ratings and key manufacturing data so technicians and owners can identify the unit and specifications quickly and accurately. What it does:

• Shows model and serial numbers, voltage, and manufacturing details for identification
• Helps replacement parts and service information
• Assists technicians during diagnostics and maintenance
• Supports safe power and connection checks by showing rated electrical info

• Clean and dry the mounting surface before applying the label for best adhesion
• Peel backing and press firmly; avoid stretching or wrinkling during placement
• Replace only with the exact OEM label to preserve accurate unit information

This replacement appliance label provides the factory identification and safety information fastened to the appliance so you can read model/serial and safety/warning text clearly. It restores legible markings for servicing and ownership records. What it does

• Shows the appliance identification, model/serial or rating area and factory safety/warning text so technicians and owners can service data.
• Helps ensure required safety and operating instructions remain visible and readable.
• Replaces a torn, faded, or missing label that can make identification and troubleshooting harder.
• Supports accurate parts ordering and service by restoring the original markings.

• One replacement label

• Peel-and-stick replacement; clean and dry the surface thoroughly before applying.
• Align carefully and press from one edge to the other to avoid bubbles; firm pressure ensures adhesion.
• Do not stretch or trim the label unless explicitly specified by the equipment instructions.
• For safety, disconnect power or follow manufacturer safety precautions before working near electrical components.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This is a replacement mounting screw used to fasten appliance panels, trim, or components. It restores secure attachment and helps eliminate rattling, loose parts, or misaligned panels for a clean, stable fit. What it does:

• Secures panels, brackets, or trim to the appliance chassis
• Stops vibration-related rattles and movement from loose fasteners
• Keeps components aligned for proper operation and appearance
• Replaces lost or stripped screws to restore factory fit

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and do not overtighten; stop when snug to avoid damage
• Inspect surrounding parts and replace as needed

Replacement lever for microwave door or latch mechanisms. Installs to operate control arms and moving parts. Needed when original is cracked, broken, or worn.

This is a small plastic lever located on the right side of the microwave door assembly that actuates the door interlock safety switch. It ensures the microwave detects when the door is properly closed before allowing operation. Replace this lever if your microwave won't start, runs with the door open, or if the lever is cracked or broken.

This is a small silicone packing seal that fits around the turntable motor shaft where it passes through the microwave floor. It prevents moisture, grease, and food debris from reaching the motor and internal components below the cooking cavity. Replace this seal if you notice leaking beneath the turntable plate or if the original seal has become brittle, torn, or displaced.

Replacement trim panel for built-in microwaves. Installs around the outer frame to cover gaps and provide a finished look. Order when cracked or damaged.

Replacement trim panel for built-in microwaves. Covers the outer frame edge for a finished look. Order if your existing trim is cracked or missing.

This holder is a small mounting bracket that secures internal appliance components to prevent movement and maintain proper alignment, helping reduce noise and keep parts functioning reliably. What it does:

• Secures and positions an internal component or assembly to the appliance frame
• Prevents shifting or sagging that can cause rattling or misalignment
• Helps maintain proper spacing for connected parts to operate correctly
• Reduces noise caused by loose fittings or vibration

• Recommended for users comfortable with appliance repair; disconnect power before servicing
• Remove adjacent panels or components as needed for access; keep fasteners organized
• Inspect mating surfaces and replace any damaged screws or clips for a secure fit

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Installation tool for mounting built-in microwave ovens. Required for proper alignment during install. Replace if missing, damaged, or worn from use.

This installation tool assists with mounting and securing your microwave during setup. Replace if lost, damaged, or missing from your original kit.