Parts for Electrolux E30SO75ESS: 03 - Oven / Cabinet Parts

Microwave runs but won't heat, or stays on when door opens? A faulty door switch is the likely cause. DIY repair takes about 30 minutes with basic tools.

If your microwave turntable won't rotate or makes grinding noises, this motor is likely the fix. Common repair for non-spinning trays. Moderate DIY.

Microwave not heating? This capacitor provides power boost to start the magnetron. Common failure causes no heating while turntable spins normally.

Microwave won't heat but runs normally? This thermal fuse protects against overheating by cutting power when temperatures spike. Simple DIY fix.

Microwave charcoal filter removes odors and recirculates air. Replace every 6 months for optimal performance. Verify fit with your model number.

Connects the turntable motor to the rotating glass tray in your microwave. Replace if the coupler is cracked, broken, or missing and the tray won't rotate.

This replacement angle is a small metal mounting bracket used to secure components in place on compatible Frigidaire appliances. It restores proper positioning and support for panels or assemblies that rely on a fixed bracket. What it does

• Provides a sturdy mounting point to hold panels, rails, or small assemblies in alignment.
• Replaces bent, cracked, or missing brackets that allow shifting or vibration.
• Helps stop rattling, misalignment, or loose panels caused by a damaged bracket.
• Works as a direct-fit hardware piece when the original bracket is worn or broken.

• Installer should turn off power to the appliance and unplug before starting work.
• Use appropriate hand tools; bracket fasteners may require small screws or bolts.
• Keep track of removed fasteners and any shims or spacers—reinstall in the same order.

Replace your microwave door gasket to restore a proper seal and prevent heat loss. Fixes worn or damaged seals for consistent heating. Verify fit.

This rubber mounting cushion cushions and isolates appliance components to reduce vibration, noise and wear. It protects contacts and trim while helping parts stay securely positioned for reliable daily operation. What it does:

• Dampens vibration and reduces rattling or buzzing during operation
• Protects edges and surfaces from metal-to-metal contact and wear
• Helps hold panels or components in proper alignment
• Absorbs shock from door or component movement to prevent damage

• One rubber mounting cushion

• Disconnect power before accessing internal panels or parts
• Remove trim or fasteners as needed to reach the mounting location; note original orientation for correct placement
• Press or seat the cushion fully into its mounting slot; replace any retaining clips if present
• If adhesive was used originally, use a compatible, appliance-safe adhesive following manufacturer instructions

This rubber cushion cushions and protects cabinet and door contact points, reducing noise, vibration, and wear. It restores a snug, quiet fit where plastic or metal parts meet and helps stop rattling or door misalignment. What it does:

• Absorbs impact between door, drawer or cabinet components to prevent metal-on-metal contact
• Reduces vibration and rattling that can occur from loose or worn bumpers
• Helps maintain proper door/drawer alignment and smooth closing
• Worn or missing cushions can cause noise, scraping, or uneven gaps

• One replacement rubber cushion

• Disconnect power and remove any panels or trim needed to access the worn cushion
• Most cushions press into a hole or slot; gently push into place until fully seated
• Inspect surrounding mounting area for damage or buildup and clean before installing
• Use basic hand tools; if adhesive was used originally, replace with appropriate adhesive rated for appliance plastics if needed

This replacement cushion is a small rubber damper that helps isolate and support appliance components to reduce vibration and prevent wear. It restores stable contact points for smoother, quieter operation. What it does:

• Absorbs vibration and reduces noise where panels or components meet
• Cushions and protects parts from impact and wear
• Helps maintain proper alignment of mounted parts
• Can prevent rattling or movement that results from worn or missing cushions

• Cushion

• Disconnect power and water before servicing the appliance
• Use basic hand tools and avoid sharp prying that can tear the cushion
• Replace all matching cushions for even performance

Label for built-in microwaves and wall oven combos. Replace worn, faded, or missing labels to restore appliance appearance and model information display.

This replacement appliance label provides the factory identification and safety information fastened to the appliance so you can read model/serial and safety/warning text clearly. It restores legible markings for servicing and ownership records. What it does

• Shows the appliance identification, model/serial or rating area and factory safety/warning text so technicians and owners can service data.
• Helps ensure required safety and operating instructions remain visible and readable.
• Replaces a torn, faded, or missing label that can make identification and troubleshooting harder.
• Supports accurate parts ordering and service by restoring the original markings.

• One replacement label

• Peel-and-stick replacement; clean and dry the surface thoroughly before applying.
• Align carefully and press from one edge to the other to avoid bubbles; firm pressure ensures adhesion.
• Do not stretch or trim the label unless explicitly specified by the equipment instructions.
• For safety, disconnect power or follow manufacturer safety precautions before working near electrical components.

This replacement identification decal restores legible equipment labeling so model, rating and safety information are visible for service and ownership. It helps replace faded, torn or peeling labels to improve readability and compliance. What it does:

• Provides a clear, adhesive identification decal with printed model/rating/safety information
• Replaces faded, torn or peeling factory labels that are hard to read
• Helps owners identify the appliance correctly during service
• Maintains visible safety and rating information required for repair or inspection

• Clean and dry the installation surface thoroughly before applying
• Peel backing and press decal firmly, smoothing out air bubbles for full adhesion
• Do not stretch, reposition repeatedly, or apply to wet/oily surfaces
• If label covers a vent or operational opening, confirm placement with service manual

Replacement mounting screw for microwave ovens. Secures internal components and panels. Needed when original screws are stripped, missing, or damaged.

Replacement mounting screw for microwave panels, brackets, and trim. Needed when original fastener is missing, stripped, or damaged during repair work.

This is a replacement screw used to secure interior and exterior appliance panels and small components, restoring secure attachment and eliminating loose or rattling parts. Ideal when original fasteners are missing or damaged. What it does:

• Secures trim, access panels, brackets, and small assemblies
• Stops rattling, vibration noise, and loose panel movement
• Replaces missing, worn, or stripped fasteners to restore fit
• Works as a direct-fit fastener where the OEM screw is specified

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid cam-out or damage
• Thread by hand to avoid cross-threading, then tighten snugly—do not overtighten

Mounting screw for microwave installation and assembly. Replaces lost, stripped, or damaged screws that secure panels, brackets, or components.

Screw secures the door latch and upper hinge plate on your microwave. Replace if missing, stripped, or loose to properly fasten door hinges and latch.

Replacement mounting screw secures panels, trim, and components in microwaves. Needed when original screws are stripped, missing, or lost during repairs.

Replacement mounting screw secures panels, trim, and components in microwaves. Needed when original screws are stripped, missing, or lost during repairs.

This rubber cushion is a small replacement bumper that reduces vibration, cushions moving parts and helps prevent noise or wear from metal-to-metal contact. It restores quiet, stable operation for the part it supports. What it does:

• Acts as a shock absorber to reduce vibration and rattling
• Protects surfaces and components from direct contact and wear
• Helps maintain proper spacing and alignment for moving assemblies
• Common symptom: noise, vibration, or metal-on-metal contact where a bumper is missing or worn

• One replacement cushion

• Safety first: disconnect power before servicing electrical appliances
• Inspect the mounting area and remove debris before installing the new cushion
• Most cushions press into place; no special tools usually required
• If adhesive or fasteners are present on the old cushion, retain or replace them exactly as found

Mounting screw for microwave installations. Secures cabinet or wall mounting brackets. Replace if missing, stripped, or damaged during reinstallation.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Installation tool for mounting built-in microwave ovens. Required for proper alignment during install. Replace if missing, damaged, or worn from use.

This installation tool assists with mounting and securing your microwave during setup. Replace if lost, damaged, or missing from your original kit.