Parts for Ge PSB1201NSS01: 03 - Oven Cavity Parts

This adhesive foam seal tape provides a slim, flexible sealing strip used to restore a tight seal around appliance openings. It helps reduce air leaks, moisture intrusion and improves temperature stability for refrigerators and freezers. What it does:

• Creates a compressible, airtight seal where original foam tape has worn or separated
• Helps reduce warm air infiltration and frost buildup that can affect cooling performance
• Minimizes moisture and dust entry at door edges or panel seams
• Restores contact between mating surfaces to improve energy efficiency

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim tape to fit; peel backing and press firmly in place along the seam or edge
• Replace only the lengths required; avoid stretching the tape during installation
• Disconnect power or follow manufacturer safety guidance

This flat case is the replacement housing that secures and protects internal components, restoring proper fit and reducing movement or noise. It returns panels and assemblies to their intended alignment for reliable operation. What it does:

• Provides a stable mounting enclosure for internal parts and wiring
• Protects components from dust, debris and incidental contact
• Helps prevent vibration-related noise or rubbing of adjacent parts
• Restores correct panel alignment and fit where the case is damaged or warped

• Disconnect power to the appliance before beginning any repair
• Minimal hand tools typically required; access may require removing panels
• Handle edges carefully; use gloves if needed to avoid cuts

This door switch access cover replaces the plastic access panel that protects and secures the door latch/switch assembly behind the appliance door. It restores a finished appearance and helps keep the switch area safe and stable. What it does:

• Covers and secures the door switch area to prevent debris contact and accidental interference
• Helps maintain proper alignment of the door switch and latch components
• Stops light drafts and reduces rattles around the door switch opening
• Common symptom: cracked, broken, or missing cover causing loose switch or exposed switch components

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the door inner panel or trim as needed to access the switch area; retain fasteners for reassembly
• Align cover over the switch opening and secure with the original screws/clips; do not overtighten
• If any switch or latch parts are damaged, inspect and replace those components separately

The Plate Bottom is an OEM part for GE microwave ovens. It forms the base surface area that internal microwave components are securely mounted and attached to. 

Causes of failure include warping and cracking of the metal shelf from prolonged exposure to high temperatures.  

Symptoms of a bad plate bottom include:

• Visible distortions or cracks in the metal material  
• Loose mounting locations for interior assembly parts
• Air gaps impairing heat dissipation from components  
• Eventual failure of attached parts over long term use

This OEM GE replacement is also compatible with Hotpoint, RCA and select Kenmore microwave models.

This bottom trim is the lower kickplate piece that finishes the appliance front, protecting and covering the area beneath the door for a clean appearance and to help keep debris out of the cabinet. What it does

• Covers and finishes the lower front of the appliance for a clean look
• Protects the base area from spills, dirt and small object entry
• Hides and helps secure the lower access area and components
• Replaces cracked, bent or missing lower trim that causes gaps or loose fit

• One bottom trim piece as shown

• Disconnect power to the appliance before starting work
• Typically fastens with screws or push clips behind the lower access panel; keep hardware from the original part for reinstallation
• Align tabs and secure evenly to avoid gaps or distortion
• Handle trim carefully to avoid scratches; use proper trim-friendly tools

This mount is a replacement support bracket that secures internal components and helps keep assemblies aligned for reliable operation. Replacing a damaged mount restores proper fit and reduces vibration and noise from loose parts. What it does:

• Secures and supports appliance panels or internal assemblies to maintain proper alignment
• Prevents movement that can cause rattling, vibration, or uneven operation
• Helps ensure connected components stay in the correct position for normal function
• Commonly used when mounts are cracked, bent, or missing

• Disconnect power (and water if applicable) before starting any repair
• Use basic hand tools; inspect surrounding fasteners and replace if damaged
• Handle sharp sheet-metal edges carefully and wear gloves and eye protection
• Replace all affected mounts for best results

The Canopy Mica is an OEM part for GE microwaves. This part covers the waveguide channel, preventing food particles and grease from entering the microwave's internal mechanisms.  

Causes of a bad canopy mica can include exposure to high levels of moisture or grease, physical damage such as cracks or burns, and general wear and tear over time.  

Symptoms of a bad canopy mica include:

• Sparks or arcing during microwave operation
• Burn marks or discoloration on the mica sheet
• Unusual noises while the microwave is running
• Uneven cooking or heating of food

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This turntable motor drives the glass tray in your microwave for even heating. Replace it when the tray stops turning, turns intermittently, or the motor makes unusual noises to restore smooth, reliable rotation.

• Rotates the turntable tray/plate for more even cooking and reheating
• Provides steady drive to the tray via the center coupler
• Typical fix for a non-spinning or intermittently spinning turntable
• Can address loud humming or grinding noises from beneath the oven floor

• Disconnect power before servicing; microwaves contain high-voltage components
• Access is typically from the bottom by removing the motor cover or base panel
• Note wire orientation; transfer connectors, align the shaft with the coupler, and secure with the original screws
• After reassembly, place a microwave-safe cup of water on the tray and run briefly to ensure the turntable rotates