Parts for Ge SCB1000KCC02: 03 - Oven Cavity Parts

This adhesive foam seal tape provides a slim, flexible sealing strip used to restore a tight seal around appliance openings. It helps reduce air leaks, moisture intrusion and improves temperature stability for refrigerators and freezers. What it does:

• Creates a compressible, airtight seal where original foam tape has worn or separated
• Helps reduce warm air infiltration and frost buildup that can affect cooling performance
• Minimizes moisture and dust entry at door edges or panel seams
• Restores contact between mating surfaces to improve energy efficiency

• Clean and dry the mounting surface thoroughly before applying for best adhesion
• Measure and trim tape to fit; peel backing and press firmly in place along the seam or edge
• Replace only the lengths required; avoid stretching the tape during installation
• Disconnect power or follow manufacturer safety guidance

This door switch access cover replaces the plastic access panel that protects and secures the door latch/switch assembly behind the appliance door. It restores a finished appearance and helps keep the switch area safe and stable. What it does:

• Covers and secures the door switch area to prevent debris contact and accidental interference
• Helps maintain proper alignment of the door switch and latch components
• Stops light drafts and reduces rattles around the door switch opening
• Common symptom: cracked, broken, or missing cover causing loose switch or exposed switch components

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the door inner panel or trim as needed to access the switch area; retain fasteners for reassembly
• Align cover over the switch opening and secure with the original screws/clips; do not overtighten
• If any switch or latch parts are damaged, inspect and replace those components separately

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing

Support bracket that secures internal components and keeps assemblies aligned in microwaves. Replace if cracked, broken, or missing to restore fit.

This is a thin mica sheet that covers the waveguide opening inside the microwave cooking cavity. It protects the magnetron and waveguide from food splatter and moisture while allowing microwave energy to pass through into the cooking area. Replace it if the cover is scorched, cracked, or has burn marks, which can cause sparking or arcing during operation.

Truss head tapping screw for microwave assembly. Secures internal components and panels. Replace if screw is stripped, missing, or lost during repair.

This light trim is the plastic bezel that surrounds and secures the oven/microwave interior light, restoring a finished appearance and protecting the light assembly from debris. It helps the light stay properly seated and keeps the opening neatly covered. What it does

• Covers and secures the interior light housing so the bulb and socket stay in place
• Protects the light opening from grease, food splatter and debris
• Restores a finished, OEM look to the appliance interior
• Can be replaced when cracked, chipped, warped or when the light opening is exposed

• One light trim/bezel

• Disconnect power to the appliance before beginning any service
• Remove any damaged trim pieces and clean the mounting area before installing the new bezel
• Typically secures with snap tabs or a couple of screws—use appropriate hand tools and avoid overtightening
• If the light bulb or socket is damaged, replace those parts separately

This right-side door hinge assembly secures and aligns the refrigerator door, restoring smooth opening and proper closure. Replaces a worn or damaged right hinge to reduce sagging and improve door seal performance. What it does:

• Provides the mounting point and pivot for the refrigerator door on the right side
• Restores proper door alignment and prevents door sag or uneven gaps
• Helps maintain an effective door seal to protect interior temperature
• Fits as the factory replacement right hinge assembly for compatible GE refrigerators

• One right-side door hinge assembly

• Support the door while removing/installing the hinge to avoid injury or damage
• Keep fasteners and hinge orientation consistent with factory locations; adjust alignment as needed
• Disconnect power to the appliance before starting work

This is a bottom panel assembly kit for an over-the-range or built-in microwave oven. It forms the lower structural section of the unit, helping to enclose internal components and support the appliance. Replace this kit if the bottom panel is dented, rusted, or damaged, which can affect the fit and appearance of the microwave in its mounting location.

Fix a microwave turntable that won't spin or turns intermittently. This motor drives the glass tray for even heating. DIY repair in 20 minutes or less.