Parts for Kitchenaid KUCC151LPA2: 05 - Panel And Control Parts

Fix a compactor that won't start when the door closes. This actuator switch kit includes a redesigned, more durable switch. DIY install in 30-60 minutes.

This retainer bracket secures internal components in place to restore proper alignment and support. It replaces a worn or broken bracket to help reduce rattling, misalignment, or loose parts during operation. What it does:

• Holds and supports internal assembly parts to maintain correct positioning
• Prevents movement that can cause noise, vibration, or rubbing
• Restores stability after bracket damage or wear
• Works as a direct-fit replacement when the original bracket is broken or bent

• High-level replacement — basic hand tools required;
• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding parts and hardware; replace any damaged fasteners for a secure fit

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Fix a cracked, faded, or missing control panel trim on your compactor. This flat console kit restores the finished appearance and protects controls.

Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.

This rotary start-run switch controls power to the appliance motor. Turning the knob engages the motor circuit to start and keep it running, restoring reliable on/off operation when the original switch wears out.

• Controls motor power using a rotary action
• Replaces a worn or intermittent switch that causes no start, stops, or inconsistent operation
• Helps resolve issues like fan/blower not turning on, cutting out, or only running in certain positions
• Designed for correct fit and dependable switching in compatible units

• Disconnect power before servicing to prevent electrical shock
• Note wire locations or take photos before removing the old switch
• Transfer wires to the same terminals on the new switch; secure connections firmly
• Test operation before reassembling any panels or knobs

Fix a broken or loose compactor control with this rotary switch knob. Restores easy setting selection when your dial is cracked, worn, or hard to turn.

Secures the rotary control switch to your trash compactor's front panel. Replace if stripped, missing, or loose to keep the control knob stable and aligned.

Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.

Fix a compactor that won't start when the door closes. This actuator switch kit includes a redesigned, more durable switch. DIY install in 30-60 minutes.

Fan mount assembly for trash compactors. Secures and supports the cooling fan in place. Replace if cracked, broken, or missing to restore proper fit.

Fan mount assembly for trash compactors. Secures and supports the cooling fan in place. Replace if cracked, broken, or missing to restore proper fit.

Size: 10-24 x 3/8 inch.

This Off switch controls power to the appliance circuit, restoring reliable on/off operation when the original switch is worn or fails. It provides a direct replacement to stop power flow and restore user control. What it does:

• Opens the circuit to stop power when switched off
• Replaces a broken, stuck, or unresponsive power switch
• Helps resolve symptoms like the unit not turning off or intermittent power
• Restores tactile on/off control at the user interface

• Disconnect power at the breaker or unplug the appliance before starting
• Remove the control panel or access cover to reach the switch; keep track of screws and fasteners
• Match terminals and wiring orientation; swap the old switch for the new one exactly

Replaces a broken, cracked, or missing air freshener cover on your trash compactor. Shields and secures the charcoal deodorizer cartridge in place.

Charcoal filter eliminates odors in your trash compactor. Replace every 2-3 months or when odors appear. Confirm fit with your model number.

Fan mount assembly for trash compactors. Secures and supports the cooling fan in place. Replace if cracked, broken, or missing to restore proper fit.

S-clip secures components in your trash compactor. Replace if bent, broken, or causing rattling noises. Verify fit with your model number.