Bosch Refrigerator B30BB935SS Parts

Bad taste or odor in water and ice? This refrigerator water filter removes impurities for clean, fresh-tasting water. Easy DIY install in minutes.

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

Secures components inside the freezer compartment. Replace if broken, cracked, or missing to keep parts properly positioned during door operation.

Small retaining clip that secures panels, trim, or covers inside your refrigerator. Replace when worn, broken, or missing to restore tight fit.

Secures shelves, door bins, and internal components in your bottom-mount refrigerator. Replace this clip if it's cracked, broken, or missing to restore stability.

The FIXTURE is an OEM replacement part for Bosch freezers. Typically located inside the fresh food compartment, fixtures hold slidable wire shelves, bins, crispers, and other removable storage accessories in precise positions.

Causes of a faulty fixture can include cracking or breaking of plastic rails from repeated impact or overloading. Clips and mounting attachments may also loosen over time.

Symptoms of a bad fixture include: 

• Shelves, bins, and pans that no longer slide smoothly or feel insecure
• Storage accessories like crispers that tilt or are difficult to remove
• Interior rattles or banging noises coming from loose components

This replacement Bosch fixture returns stability and structure to the organization system. Realigning fixtures maintains consistent placement and secure engagement of accessories for tidy, accessible food storage. 

Compatible with Thermador, Gaggenau, or Kenmore French door models utilizing consistent interiors.

If your refrigerator isn't making ice or produces hollow cubes, this ice maker assembly may need replacement. Moderate DIY repair restores ice production.

Mounting hardware kit secures refrigerator components in place. Replaces worn, missing, or damaged fasteners that cause rattling or loose parts inside unit.

This hinge pin secures the door hinge mechanism and allows your refrigerator or freezer door to pivot smoothly. It maintains proper door alignment and prevents the door from sagging or binding. Replace this part if your door won't close properly, sags when opened, or if you hear squeaking or grinding when opening the door.

Electronic power module for the dishwasher. This is the main control board that manages power and timing for wash, drain, and drying functions, helping restore normal operation when the original module has failed or is intermittent.

• Regulates incoming power and switches major loads (circulation pump, drain pump, heater, inlet valve)
• Coordinates cycle logic based on door and sensor inputs
• May help when the dishwasher won't power on or start a cycle
• May help when cycles stop mid-way, don't complete, or drying performance is poor

• Disconnect electrical power at the circuit breaker before servicing
• Access is typically from behind the lower toe panel/base; remove panels as needed
• Photograph and label wiring; transfer any mounting hardware; seat connectors fully
• Use ESD protection and handle the board by its edges only

The DIODE-LED is an OEM part for Bosch refrigerators. As a vital light-emitting part, it illuminates interior refrigerator lighting and display screens. Discreetly housed inside light fixtures and control panels, the DIODE-LED emits a soft glow using integrated semiconductor technology.

Causes of a bad DIODE-LED can involve failures in the chip or wire connectivity over time due to repeated thermal cycling. Impacts or wire degradation inside refrigerators can damage the delicate LED.

Symptoms of a bad DIODE-LED include:

• Dim or completely burned-out interior lighting
• Dark display screens that won't illuminate
• Individual lights or entire fixtures going out

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Routes water around the fine filter area when servicing your dishwasher. Replace if damaged or missing to maintain proper wash circulation. Verify fit.

Replace a frayed or damaged power cord that's causing no power or intermittent operation. Direct plug-in replacement restores safe electrical connection.

This factory strip is a trim piece that finishes and protects an exposed edge or gap on your appliance. Replacing a cracked or missing strip restores a clean look and helps panels align and stay secure. What it does

• Finishes an exposed seam or edge as designed by the manufacturer
• Helps keep adjacent panels aligned and secure
• Can reduce vibration-related rattles when properly seated
• Common signs of failure: loose or missing trim, visible gaps, warping, cracks, or buzzing/rattling noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Note the strip's orientation; remove any screws/clips and gently release tabs
• Reuse or transfer original fasteners/clips as required by your model
• Align carefully and avoid overtightening to prevent damage to the strip or surrounding panels

This evaporator fan circulates cold air through the freezer/refrigerator evaporator to help maintain even cooling and proper temperature. Replacing a worn or noisy fan can restore airflow and improve cooling performance. What it does:

• Moves air across the evaporator coil to distribute cold air throughout the compartment
• Helps prevent frost buildup by maintaining steady airflow over the evaporator
• A noisy, vibrating, or non-spinning fan can cause poor cooling or uneven temperatures
• Restores proper circulation when the original fan motor or blade is damaged or fails

• One evaporator fan assembly

• Disconnect power to the appliance before attempting any repair to avoid electric shock
• Access may require removing interior panels or the evaporator cover; follow OEM diagram for your model
• Handle the fan blades and motor carefully to avoid bending blades or damaging the motor shaft