Gaggenau Freezer RB492301 Parts

The Lock Clamp is an OEM replacement part for Bosch refrigerators. It is a fitting that secures the freezer drawer in its closed position. Made of durable metal and plastic, the lock-clamp features a latching mechanism to fasten the door shut with an audible click. 

Symptoms of a bad lock clamp include:

• The freezer door not closing or latching securely
• Warm air escaping from around the door seal  
• Noise from a loose or poor-fitting lock-clamp
• The door popping open unexpectedly

Causes of a bad lock clamp can include wear and tear of moving parts over time, broken clips or latches from repeated use.

This OEM Bosch replacement lock clamp is compatible also with Thermador and Gaggenau model refrigerators

Refrigerator door seal creates an airtight barrier to maintain internal temperature. Replace if cold air escapes or condensation forms. Confirm fit with model.

This slide rail retainer secures the freezer drawer or shelf rails in their proper position within your freezer compartment. It prevents the rails from shifting or coming loose during normal use of the drawer system. Replace this part if your freezer drawer doesn't slide smoothly, falls off its track, or if the rails have become loose or misaligned.

Secures freezer baskets to drawer rails in your refrigerator. Replace if clip is cracked, broken, or missing to keep bins properly mounted and stable.

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

Secures components inside the freezer compartment. Replace if broken, cracked, or missing to keep parts properly positioned during door operation.

This temperature limiter safeguards the evaporator defrost heater by opening the circuit if temperatures rise too high. Replacing a failed limiter restores defrost safety and helps prevent frost buildup and inconsistent cooling performance.

• Protects the defrost circuit by cutting power to the evaporator heater when an over-temperature condition is detected
• An open/failed limiter prevents the heater from energizing, causing frost accumulation on the evaporator and warm refrigerator temps
• Designed to be installed in the original location and orientation for accurate temperature sensing

• Disconnect power before servicing; evaporator fins and sheet metal are sharp—use cut-resistant gloves
• Access the evaporator compartment and note the limiter's original mounting and wire routing before removal
• Transfer any clips/insulation sleeves and reconnect wiring to the same terminals; do not bypass this safety device
• Reassemble, restore power, and monitor for normal defrost operation

Small retaining clip that secures panels, trim, or covers inside your refrigerator. Replace when worn, broken, or missing to restore tight fit.

Inline connector that joins internal water hoses in your refrigerator. Replace if leaking or connections are loose to restore sealed fit. Confirm compatibility.

Secures shelves, door bins, and internal components in your bottom-mount refrigerator. Replace this clip if it's cracked, broken, or missing to restore stability.

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation

Refrigerator not cooling properly or running constantly? The temperature sensor monitors internal temps and signals the control board. DIY-friendly repair.

This replacement rail supports a dishwasher rack and restores smooth, stable sliding for loading and unloading. It helps keep the rack aligned so dishes move in and out without catching or tilting. What it does:

• Provides a smooth track for the dishwasher rack to roll on
• Keeps the rack properly aligned to prevent binding or tipping
• Reduces noise and rough movement caused by a worn or damaged rail
• Replaces cracked, bent, or broken rails that stop the rack from sliding

• One replacement rail

• Disconnect power and water to the appliance before starting any repair
• Remove the affected rack before replacing the rail to access mounting points
• Inspect mounting clips or rollers and replace any that are damaged for proper fit
• Handle edges carefully and reassemble components securely; test rack movement after installation

Leveling foot installs at the refrigerator base to support and level the unit. Replace if worn, cracked, broken, or missing to restore stability.

Factory mounting housing fixture that secures components inside your refrigerator. Replace if cracked, broken, or missing to restore proper support and alignment.

Mounting hardware kit secures refrigerator components in place. Replaces worn, missing, or damaged fasteners that cause rattling or loose parts inside unit.