Kenmore Refrigerator 363.48047894 (36348047894, 363 48047894) Parts

• Freezer section too warm
• Noisy

My refrigerator's cooling fan was making a noise. It wasn't loud; in fact, it was barely discernible. However, it was just loud enough to annoy me. The fan blade was hitting the shroud every now and then, creating a subtle, yet annoying sound. I'd tried tightening all the screws back there, and it helped-for a while. The noise came back. After looking at the fan motor, I noticed the bushings; it occurred to me that they might be the culprit. And why not? They were the originals installed at the... Read more

We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

• Won't start
• Fridge runs too long
• Frost buildup
• Fridge too warm

After reviewing a number of testimonials and your videos from your APP.com site I determined my most likely problem was either the defrost heater, thermostat, timer or possibly all three. The real challenge now began. Getting to the specific parts with my specific model number was a real challenge. It was not as easy as removing the light guard and 5 screws since my model had two Track Cant Shelf vertical rails restricting the removal of the back panel. Also, these rails could not be removed... Read more

• Freezer too cold
• Fridge too cold
• Too warm
• Freezer section too warm

Yes, a 49-yr old woman fixed this fridge all by herself! AppliancePartsPros was very helpful in the diagnosis of the problem, which I determined to likely be the result of defrost failure. There was a large amount of ice and frost coating the back of the freezer despite the inside temp being 42 degrees. My husband thought I was crazy to think it was a problem with ice when the temperature was warm, but I told him to trust me and I would attempt the repair. He just wanted to throw the old one... Read more

• Fridge runs too long
• Door won't open or close
• Door sweating

I followed the directions on the video.....had to look at it a couple of time. Difficult to work lying on the floor for me, but the technique was spot on. I have now replace the door closing cams on the refrigerator door and the freezer door of the side by side unit. Thanks for such great instructions. Read more

• Light not working

I researched the model and watched a YouTube video on the repair. I ordered the part. Two days later it arrived and I made the repair. I'm all thumbs in home repairs, but had it done in 5 minutes. My husband was surprised. Nice that I can take care of a few simple repairs around the house. Read more

• Fridge too warm
• Fridge runs too long
• Freezer not defrosting
• Freezer section too warm

My GSS20IETD BB side-by-side refrigerator had been having the ice form into a single mass over a period of a week after cleaning it out. It actually kept breaking my ice maker auger and pushing the slide-in tray or shelf over the ice maker up breaking it also. Frost would form all over food after about a couple of weeks. The ice auger motor would freeze up and stop turning. The coils did not have frost on them when I was able to view them. I replaced the thermistors in the freezer, defrost the... Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

• Noisy

I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more

• Leaking
• Ice maker not making ice

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

• Won't start

I bought this relay switch and it works great. On the left side of the compressor there is a plastic cover you pry off with a screw driver. The relay switch had one wire plug on it. Just pull the wire off and the pull the relay switch off the compressor. Read more

I made a lucky guess when I ordered the part as I had no model # or anything to go by. I just ordered what looked like the right thing and it was the exact part for my fridge. Replacement was easy. Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more