Kenmore Refrigerator 363.69967991 (36369967991, 363 69967991) Parts

• Freezer section too warm
• Noisy

My refrigerator's cooling fan was making a noise. It wasn't loud; in fact, it was barely discernible. However, it was just loud enough to annoy me. The fan blade was hitting the shroud every now and then, creating a subtle, yet annoying sound. I'd tried tightening all the screws back there, and it helped-for a while. The noise came back. After looking at the fan motor, I noticed the bushings; it occurred to me that they might be the culprit. And why not? They were the originals installed at the... Read more

I ordered a new switch from APP and fixed my fridge. However, the video posted for this repair on this site is not applicable to newer refrigerator models. I have a 2015 GE GTE18IHCRSS and had to drop the control housing (#432 in the diagram) to attach the wire/plug assembly to the switch. Only had to remove the front screw with a 1/4" nut driver and that provided enough of a gap for me to plug in the switch. So the correct method to replace the light switch in a newer model refrigerator is as... Read more

• Light not working

I researched the model and watched a YouTube video on the repair. I ordered the part. Two days later it arrived and I made the repair. I'm all thumbs in home repairs, but had it done in 5 minutes. My husband was surprised. Nice that I can take care of a few simple repairs around the house. Read more

• Fridge runs too long
• Door sweating

REPLACED DOOR GASKETS. Read more

I changed the motherboard - computer and also changed the motor in the freezer, because it was doing a howling sound every time it turned on. The repair technician asked for $500 for a repair and that is on top of the $230 I paid him two days before. I looked up the parts and decided to try myself and it paid off. Great instructional videos. Thanks Read more

• Noisy

I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the... Read more

Took about 5 min to replace the handle with the parts ordered. Thank you for the fast service. Read more

This is a 15 yr old Kenmore (GE) refrigerator with top mounted freezer... I knew, for awhile, that I had a DEFROST problem. That was causing water to collect on the inside bottom of the fridge, under the veg./fruit bins. And then occasionally run out onto the kitchen floor if I didn't sop up the water inside. But I delayed the repair because of the hassle of emptying the food, top and bottom, and finding temporary homes for it all. Until I noticed 3 things happen in short order. 1)The water... Read more

SELF. Read more

• Leaking
• Ice maker not making ice

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

• Fridge too warm

First I took the technical data sheet off the back of the unit, it was in a brown envelop taped and tucked into the lower equipment cover. Then I compared information from Appliance Parts Pros to the data sheet, matched up the probable culprit parts, and ordered defrost thermostat and defrost control. They arrived promptly.. Unplug the unit from the wall. The defrost control is located in the same space as the light, two screws and the small panel drops down, a tip is to use a short #2... Read more

REPLACED DOOR GASKETS. Read more

Inspected the Defrost timer and it seamed to be functioning properly. Ohm ed out the defrost heater element and it also measured out correctly (mine 34 ohms). Bypassed the heater element and found that the unit would run without tripping breaker during defrost cycle. At this point i inspected the wiring to the heater and checked continuity of the wire and continuity to ground, No issues found. So with the heater out of the circuit and not having an issue i ordered heater element from... Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more

I researched the problem and determined that the only thing that can cause this was compressor bad or not starting. Since it was cold the day before I felt it had to be the starter parts and ordered them. It was also very important to clean the coil which I believe caused the over heating. Read more