Bosch Refrigerator B36IT800NP Parts

If your refrigerator cabinet feels warm or cooling is weak, the condenser fan may have failed. This fan circulates air over the condenser coil to remove heat.

This factory strip is a trim piece that finishes and protects an exposed edge or gap on your appliance. Replacing a cracked or missing strip restores a clean look and helps panels align and stay secure. What it does

• Finishes an exposed seam or edge as designed by the manufacturer
• Helps keep adjacent panels aligned and secure
• Can reduce vibration-related rattles when properly seated
• Common signs of failure: loose or missing trim, visible gaps, warping, cracks, or buzzing/rattling noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Note the strip's orientation; remove any screws/clips and gently release tabs
• Reuse or transfer original fasteners/clips as required by your model
• Align carefully and avoid overtightening to prevent damage to the strip or surrounding panels

If your appliance won't start, cycles won't advance, or displays are blank, this electronic control board restores cycle selection and timing control.

Fixes unresponsive controls, display errors, or cycle failures in refrigerators and freezers. Direct replacement for failed main control modules.

This replacement strip restores a clean, factory fit where it's used on the appliance. Replacing a worn or missing strip helps secure adjoining pieces, maintain spacing, and eliminate unsightly gaps or vibration-related noise. What it does:

• Acts as a finishing/spacer strip between adjoining components
• Helps hold trim or panel pieces in the correct position
• Maintains alignment and clearances to prevent rubbing or rattling
• Common symptoms: cracked or missing strip, visible gap, loose trim/panel, buzzing or vibration noises

• 1 strip

• Disconnect power and, if applicable, shut off water before servicing
• Refer to your model's parts diagram for the correct orientation and attachment points
• Reuse original screws/clips if required; hardware is typically model-specific
• After installation, verify proper alignment and operation of adjacent panels/doors

Installation hardware set for refrigerators. Includes mounting brackets, screws, and fasteners needed to secure your appliance during setup or replacement.

Fixes ice buildup in refrigerator gutter systems. This heating element prevents ice dams and keeps drainage clear in bottom-mount refrigerators.

Fixes no water dispenser or ice maker issues. This inlet valve controls water flow to restore proper fill and prevent leaks in your refrigerator.

This is a small wheel designed for use in a refrigerator or freezer, typically mounted on a shelf, drawer, or rack to allow smooth sliding in and out. It helps support the weight of stored items while enabling easy access. Replace this wheel if it is cracked, broken, or no longer rolling freely, causing drawers or racks to stick or sit unevenly.

Interior cabinet divider wall that restores proper compartment separation in your refrigerator. Replaces cracked, broken, or missing dividers.

Secures and guides your refrigerator door for smooth opening and closing. Replace if your door sags, doesn't align, or fails to seal properly. Verify fit with your model number.

Factory trim strip that finishes edges and covers seams on your refrigerator. Replace if cracked, worn, or missing to restore clean appearance.

Fix ice buildup or cooling issues with this refrigerator evaporator coil. Resolves uneven temperatures and frost accumulation in freezer compartments.

This is a filter drier used in the sealed refrigeration system to remove moisture and contaminants from the refrigerant lines. It is a small cylindrical component typically located along the refrigerant tubing between the condenser and the capillary tube. Replace this part if the refrigerator or freezer is not cooling properly due to a restricted or saturated drier, typically during a sealed system repair.

This fixture is a small mounting bracket that secures internal dishwasher components to the tub, helping maintain proper alignment and reduce vibration. Replaces worn or broken brackets to restore stable operation and prevent rattling or misalignment. What it does:

• Secures internal parts and assemblies to the dishwasher tub or frame
• Keeps components aligned to prevent rubbing, noise, or premature wear
• Helps maintain proper clearance for moving parts like racks or spray arms
• Can prevent intermittent contact that might cause rattles or vibration

• Disconnect power and water supply before starting any service
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit
• Typically installs with basic hand tools; follow OEM instructions for correct placement

This power module supplies and manages electrical power to key appliance systems, restoring reliable control and operation. It replaces a failed power distribution/control board to help appliances regain proper power routing and startup capability. What it does:

• Provides regulated power distribution to the appliance's control circuits and components
• Replaces a failed module that can cause no-start, intermittent power loss, or unresponsive controls
• Helps resolve blown fuses or tripped circuits caused by a faulty power board
• Works as the central power interface between the main control and high-voltage components

What's included: One power module (single unit as shown) Install notes:

• Disconnect power at the breaker or unplug the appliance before starting; verify no voltage is present
• Handle the board by its edges and avoid touching components to prevent ESD damage
• Follow the appliance manufacturer's disassembly and reassembly steps; retain all mounting hardware unless otherwise directed