Bosch Range CM302BS Parts

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Heat-resistant seal for 30-inch ovens. Replace when worn or damaged to prevent heat loss and maintain consistent baking temperatures. Verify fit.

Replacement inner glass panel for oven doors. Installs between door layers. Needed when original glass is cracked, chipped, or shattered from impact.

This meat probe sensor is a temperature-sensing device that inserts into food while it cooks in the oven, allowing the oven to monitor the internal temperature and automatically stop cooking when the target temperature is reached. It connects to a jack inside the oven cavity via a heat-resistant cable. Replace this probe if your oven no longer reads the food temperature accurately, displays a probe error code, or if the cable or tip is visibly damaged.

Oven won't heat or shuts off during use? This thermal fuse cuts power when temperature exceeds safe limits. Moderate DIY repair with multimeter testing.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

A replacement temperature sensor (thermistor) that monitors internal temperatures and sends readings to the appliance control board. Restores accurate temperature sensing to help cycles and temperature regulation run correctly. What it does:

• Measures internal temperature and relays readings to the control board so the appliance can adjust heating/cooling cycles.
• Helps ensure proper defrost or cycle timing by providing accurate temperature feedback.
• Common symptoms of a failing sensor: inconsistent temperatures, frequent or short cycling, or temperature-related performance issues.
• Works as a direct replacement for a worn or failed sensor to restore normal temperature monitoring.

• Disconnect power to the appliance before starting any repair to avoid shock or damage.
• Handle the sensor and wiring gently; avoid kinking or pulling the lead and ensure the connector seats fully.
• Installation typically requires access behind panels or inside the compartment—keep fasteners organized and follow the service manual.

If your oven won't start or runs with the door open, this door interlock switch detects proper closure and latching. DIY repair in under an hour.

This Fan is an OEM part for Bosch Ovens. The fan ensures consistent and even distribution of heat throughout the cooking chamber.  

A common cause of a malfunctioning Fan is motor failure due to prolonged usage or accumulation of dirt and debris around the fan blades. 

Symptoms of a faulty Fan may include:

• Uneven cooking or baking results
• Unusual noises during oven operation
• Failure of the oven to reach or maintain desired temperatures

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This cooling fan assembly mounts inside the oven housing and circulates air to prevent the control panel and surrounding cabinetry from overheating during use. It typically runs during and after the oven's heating cycle to dissipate excess heat. Replace this assembly if the fan is noisy, doesn't spin, or if your oven's electronic controls are shutting down due to overheating.

This is a thermal fuse designed to protect the microwave's electrical circuit from overheating. It acts as a safety device that breaks the circuit if internal temperatures exceed safe limits. Replace this fuse if your microwave suddenly stops working or loses all power, as a blown thermal fuse is a common cause of a completely dead unit.

Fix intermittent power or component failure with this range socket electrical connector. Restores secure wiring connections in electric and gas ranges.

Oven lamp assembly provides interior lighting for viewing food during cooking. Replace when bulb burns out or housing cracks. Verify fit with your model.

Microwave not heating? A failed diode rectifier prevents proper power flow to the magnetron. This one-way current component is essential for heating function.

Replacement mounting nut for securing internal oven and range components. Needed when original fastener is stripped, missing, or damaged during repair work.

Restore even baking when your oven heats unevenly. This convection fan blade circulates hot air for consistent cooking. Moderate DIY install.