Bosch Dishwasher SGI43A12EU Parts

Light gray flip tine latch for dishwasher dishrack. Replaces broken, cracked, or missing latches that secure flip-down tines in upper or lower racks.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Secures wooden or custom exterior panels to your dishwasher door. Replace if your panel rattles, shifts, or feels loose. Confirm fit with your model.

Left side door hinge for your dishwasher. Replaces damaged, bent, or broken hinges that cause the door to fall open or swing too far. Bushing included.

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

Drain hose clamp

Replace your dishwasher's upper rack rail if cracked, broken, or worn. This guide rail installs along the sides to support smooth rack sliding.

This drain pump assembly is responsible for expelling used water from the dishwasher tub during the drain cycle. It uses an impeller driven by a small motor to push water out through the drain hose. Replace this pump if the dishwasher fails to drain, leaves standing water at the bottom of the tub after a cycle, or if you hear the pump motor buzzing or humming without actually draining.

Securing kit for dishwasher installation. Includes mounting hardware to attach your dishwasher to cabinetry. Replace if brackets are missing or damaged.

This is a mounting holder used inside a dishwasher to secure and support internal components in their proper position. It helps keep parts aligned during the wash and drain cycles. Replace this holder if it is cracked, broken, or missing, which can cause loose or misaligned parts and unusual noises during operation.

Dishwasher salt funnel guides water softener salt into the reservoir without spills. Replace if cracked or lost to maintain proper salt loading.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Connects the sump to the pressure chamber in your dishwasher. Replace if cracked, leaking, age-embrittled, or damaged. Includes 2 o-rings for secure fit.

Replacement spray arm assembly that installs in the dishwasher tub to restore water distribution. Needed when the original is cracked, worn, or missing.