Bosch Dishwasher SHE53C85N Parts

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

Fix incomplete cycles or poor cleaning caused by a faulty temperature sensor. This NTC sensor monitors water temperature to ensure proper heating and cycle timing.

Creates a watertight barrier between dishwasher components. Replace if cracked, flattened, or leaking to prevent drips. Verify fit with your model.

Factory replacement door handle for your dishwasher. Restores secure grip for opening and closing. Replace cracked, loose, or missing handles.

Lower housing that forms the structural base of your dishwasher. Replace when the original case is cracked, warped, or damaged to restore stability.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Replaces a cracked, scratched, or damaged dishwasher inner door panel. Protects internal components and restores the door interior appearance.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Replace your dishwasher's broken or missing rack handle. This handle clips to the front of the dish rack for easy gripping when sliding racks in and out.

Fix loose or rattling dishwasher components with this holder retainer. Secures parts in position to prevent movement and restore quiet operation.

This replacement rack rail restores smooth, stable sliding for a dishwasher rack, helping keep the rack aligned and reduce catching or derailment. It's the straightforward part to repair worn or damaged rack movement. What it does:

• Guides the dishwasher rack along its track so the rack opens and closes smoothly
• Replaces a bent, cracked, or worn rail that can cause the rack to stick or come off track
• Reduces noise and rubbing caused by damaged or misaligned rail components
• Helps maintain proper rack alignment for loading and unloading dishes

• Disconnect power to the appliance before servicing to prevent electrical hazard
• Remove the affected rack and any end caps or clips to access and replace the rail
• Inspect matching rail clips/wheels for wear and replace if needed for proper function

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

Replacement rack wheel that restores smooth rolling movement to your dishwasher rack. Needed when the original wheel is cracked, worn, broken, or missing.

Secures internal dishwasher components and keeps assemblies aligned. Replace this mounting clip holder if yours is cracked, broken, or missing.

The Dishwasher Installation Set is an OEM part for Bosch dishwashers. This set contains all necessary hardware for professional installation or replacement, including leveling legs, mounting brackets and anti-tip brackets. Manufactured from corrosion-resistant steel, these parts securely fasten the dishwasher into place.

Causes relate to normal wear over time from use. Improper original installation may also compromise individual parts. Failing to properly level, brace or anchor the dishwasher leads to unnecessary stresses.

Symptoms of worn or missing installation hardware include:

• Looseness, shaking or movement during operation
• Doors failing to properly self-close or seal fully
• Leaks developing around dishwasher connections
• Installation not compliant with current regulations

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.