Bosch Dishwasher SHE55C06UC Parts

Replace your dishwasher's upper rack pull-out rail assembly. Installs on top rack to enable smooth sliding. Needed when rails are cracked, broken, or wheels are worn. Includes left and right sides.

Replace your dishwasher's upper rack rail if cracked, broken, or worn. This guide rail installs along the sides to support smooth rack sliding.

Replaces damaged inner door trim that supports the door panel and seals the front edge. Replace if warped, cracked, or affecting door alignment.

Adjusting device for dishwasher height and leveling. Replaces broken, worn, or missing adjustment mechanisms. Installs at base for proper alignment.

Insulation pad for dishwashers. Installs underneath or around the tub to reduce noise and retain heat. Replace if torn, compressed, or missing.

This is a display optimizing component for a dishwasher's electronic control panel. It helps regulate and enhance the clarity and function of the digital display used to select cycles and monitor wash status. Replace this part if the display appears dim, flickering, shows garbled characters, or fails to illuminate properly.

This replacement side panel restores the appliance's exterior finish and protects the cabinet edge from dings, scratches and wear. It's a direct-fit exterior trim piece that keeps the side of the unit looking finished and secure. What it does

• Covers and protects the appliance cabinet side from impact, scratches and cosmetic damage
• Restores a clean, factory appearance when original panel is dented, chipped or missing
• Helps maintain proper clearance and panel alignment with adjacent cabinetry
• Prevents exposed edges that can catch debris or snag clothing

• Includes: one side panel

• Disconnect power (and water supply if applicable) before starting work
• Handle panel carefully — edges may be sharp; gloves recommended
• Typically secured with screws or clips; retain hardware from the original panel or refer to the appliance parts diagram

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

This tube channels water from the inlet valve to the wash system inside the dishwasher. It ensures a steady supply of water reaches the spray arms for proper cleaning during wash and rinse cycles. Replace if the tube is cracked, kinked, or leaking, which can cause poor water flow, inadequate cleaning, or water pooling under the dishwasher.

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

Spring-style hose clamp secures water and drain hoses to fittings, preventing leaks. Replace when connections loosen or clips lose tension. Confirm fit with your model number.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.

Secures the sump assembly to the tub, preventing leaks and movement. Replace if worn, cracked, or if you notice water leaking from the base of your dishwasher.