Bosch Dishwasher SHE88PZ65N Parts

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

Secures internal dishwasher components to maintain proper alignment and reduce movement. Replace when original bracket is cracked, deformed, or worn.

Secures internal components and panels with a threaded anchor point. Replace when original stud is missing, cracked, or stripped for stable mounting.

This factory replacement spring restores the correct return force in the original mechanism so parts move, hold, and release as designed—bringing back smooth, reliable operation and preventing premature wear on related components.

• Provides controlled tension/return force within the intended assembly
• A weak, stretched, or broken spring can cause sticking, weak action, or failure to hold/release
• Replace if the original is deformed, missing, corroded, or broken
• Designed to fit and function like the original for consistent performance

• Disconnect power (and shut off water supply if applicable) before service
• Springs can release suddenly—use eye protection and needle-nose pliers
• Photograph the original routing/orientation before removal to match placement
• Access points and procedures vary by model; refer to the service manual

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Inner door panel for dishwashers. Serves as protective barrier between interior tub and outer door. Replace if cracked, warped, or damaged to restore seal.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Fix loose or rattling dishwasher components with this holder retainer. Secures parts in position to prevent movement and restore quiet operation.

Fix cloudy dishes and hard water spots with this water softener regeneration valve. Restores proper brine flow during recharge cycles for cleaner dishes.

The Dishwasher Installation Set is an OEM part for Bosch dishwashers. This set contains all necessary hardware for professional installation or replacement, including leveling legs, mounting brackets and anti-tip brackets. Manufactured from corrosion-resistant steel, these parts securely fasten the dishwasher into place.

Causes relate to normal wear over time from use. Improper original installation may also compromise individual parts. Failing to properly level, brace or anchor the dishwasher leads to unnecessary stresses.

Symptoms of worn or missing installation hardware include:

• Looseness, shaking or movement during operation
• Doors failing to properly self-close or seal fully
• Leaks developing around dishwasher connections
• Installation not compliant with current regulations

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

This is a small rubber seal that fits on the water softener cap inside the dishwasher, creating a watertight barrier to prevent leaks. It ensures the water softener compartment remains properly sealed during wash cycles. Replace this seal if you notice water leaking from the softener cap area or if the rubber has become worn, cracked, or no longer provides a tight fit.

This is a plastic insert designed to fit into the dishwasher dishrack, providing additional support and organization for dishes, cups, or utensils during the wash cycle. It helps keep items securely in place to ensure thorough cleaning and prevent damage from movement. Replace this insert if it is cracked, broken, or missing, which can cause dishes to shift and result in poor cleaning or chipped items.

Insulating pad for dishwashers. Installs on the tub or door to reduce noise and retain heat. Replace if cracked, torn, or missing for proper insulation.

Secures internal dishwasher components and keeps assemblies aligned. Replace this mounting clip holder if yours is cracked, broken, or missing.

The Thread Bolt is an OEM part for Bosch dishwashers. It serves as a fastening component, securing the water inlet in place and ensuring a proper water supply connection.

Causes of a malfunctioning Thread Bolt can include cross-threading or over-tightening during installation, leading to stripping or damage.  

Symptoms of a bad Thread Bolt include:

• Leaks around the water inlet area Loose or rattling water inlet valve 
• Difficulty in accessing or removing the valve assembly 

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.