Bosch Dishwasher SHE89PW75N Parts

Fix E4 water flow errors in your dishwasher with this flow meter sensor. Monitors water volume to ensure proper fill levels during wash cycles.

Replaces the rotating spray arm shower head in your dishwasher's upper rack. Install a new one if yours is cracked, broken, or keeps falling off the tube.

The pump sump seal repair kit contains gaskets and seals that prevent water leaks in the dishwasher's drain pump assembly. Located at the bottom of the dishwasher tub where the pump connects, these seals maintain watertight connections. Replace if you notice water pooling under the dishwasher, reduced drainage performance, or visible water leaks during operation.

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Fix dishwasher not filling with water or leaking at the water entry point. This inlet ensures proper water flow and prevents leaks where water enters.

Original installation hardware set for dishwashers. Includes mounting fasteners and brackets to secure components and panels. Replace worn or missing hardware.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement mounting hardware kit for securing dishwasher panels and components. Needed when original fasteners are lost, stripped, or damaged.

Replacement trim insert for dishwasher racks. Secures panels and tines, closes gaps for proper alignment. Needed when original is cracked, broken, or missing.

Replacement mounting hardware kit for securing dishwasher panels and components. Includes fasteners and clips to restore proper support and stability.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

This factory replacement spring restores the correct return force in the original mechanism so parts move, hold, and release as designed—bringing back smooth, reliable operation and preventing premature wear on related components.

• Provides controlled tension/return force within the intended assembly
• A weak, stretched, or broken spring can cause sticking, weak action, or failure to hold/release
• Replace if the original is deformed, missing, corroded, or broken
• Designed to fit and function like the original for consistent performance

• Disconnect power (and shut off water supply if applicable) before service
• Springs can release suddenly—use eye protection and needle-nose pliers
• Photograph the original routing/orientation before removal to match placement
• Access points and procedures vary by model; refer to the service manual

Fix cloudy dishes and hard water spots with this water softener regeneration valve. Restores proper brine flow during recharge cycles for cleaner dishes.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.