Bosch Dishwasher SHEM3AY52N Parts

Fix a tilted or unstable dishwasher with this leveling leg. Ensures proper drainage and cleaning performance. Easy DIY install in minutes.

Replaces cracked, broken, or missing dishwasher base panel (toe kick). Installs at bottom front of unit. Needed when panel is damaged or missing.

Replacement cup rack for dishwashers. Installs inside the tub to hold cups and mugs during wash cycles. Replace if prongs are broken or plastic is cracked.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Secures panels, brackets, and trim pieces inside your dishwasher. Replace this fastener if stripped, missing, or damaged to restore tight assembly.

The pump sump seal repair kit contains gaskets and seals that prevent water leaks in the dishwasher's drain pump assembly. Located at the bottom of the dishwasher tub where the pump connects, these seals maintain watertight connections. Replace if you notice water pooling under the dishwasher, reduced drainage performance, or visible water leaks during operation.

Replacement door spring for dishwashers. Restores proper tension to door mechanism. Needed when original spring is broken, worn, or stretched out.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Replace your dishwasher's thermal insulation if experiencing excessive heat around the unit or noise during cycles. Protective barrier for safer operation.

Vent hose for dishwashers that guides steam and moisture out during wash cycles. Replace if cracked, disconnected, or worn to restore proper venting.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement tube for Bosch appliances that routes water or drainage between components, helping restore correct flow, reduce pooling and leaks, and maintain normal appliance performance. What it does:

• Channels water between valves, pump and drain to enable normal water movement.
• Replaces cracked, split or blocked tubing that can cause leaks or standing water.
• Helps restore proper drainage and prevent water from pooling inside or under the appliance.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect and replace any damaged clamps, seals or fittings when installing the tube.
• Route the tube exactly as the original to avoid kinks; secure with the factory clamps or equivalent.

Control panel not responding or selecting wrong cycles? This dishwasher control board processes button inputs and communicates with the main control.

Creates a watertight barrier between dishwasher components. Replace if cracked, flattened, or leaking to prevent drips. Verify fit with your model.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment