Bosch Dishwasher SHEM78Z55N Parts

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This support is a factory replacement component that holds and stabilizes a specific part within your appliance so it stays aligned and secure. Replacing a cracked or missing support restores proper fit and helps prevent noise or binding.

• Provides structural support and alignment for the designated component
• Keeps parts seated securely to minimize movement and vibration during use
• A damaged or missing support can cause looseness, rattling, sagging, or misalignment
• Restores proper fit and function when the original is cracked, warped, or broken

• Disconnect power and shut off any gas/water supplies before servicing
• Refer to your model's parts diagram to identify location and orientation
• Install using the appliance's existing screws or clips; avoid overtightening to prevent damage
• Wear cut-resistant gloves; beware of sharp edges and pinch points

Fix dishwasher not starting, intermittent power issues, or control panel errors with this wire harness. Routes electrical signals between components.

Threaded nut secures components to bolts inside your dishwasher. Replace if stripped, missing, or loose to restore proper clamping force. Confirm fit.

Creates a watertight barrier between dishwasher components. Replace if cracked, flattened, or leaking to prevent drips. Verify fit with your model.

Service tool set for dishwasher installation and repairs. Includes specialty drivers and tools for accessing fasteners and making adjustments. Needed for proper servicing.

Replace your dishwasher's cap cover plug to seal access ports and protect against moisture and debris. Restores a clean finish. Confirm fit with your model.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Factory replacement door handle for your dishwasher. Restores secure grip for opening and closing. Replace cracked, loose, or missing handles.

Lower housing that forms the structural base of your dishwasher. Replace when the original case is cracked, warped, or damaged to restore stability.

Molded plastic duct at top of dishwasher that vents steam and vapors during wash and dry cycles. Replace if cracked, broken, or missing components.

Secures internal components and panels with a threaded anchor point. Replace when original stud is missing, cracked, or stripped for stable mounting.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Fix loose or rattling dishwasher components with this holder retainer. Secures parts in position to prevent movement and restore quiet operation.

The Dishwasher Installation Set is an OEM part for Bosch dishwashers. This set contains all necessary hardware for professional installation or replacement, including leveling legs, mounting brackets and anti-tip brackets. Manufactured from corrosion-resistant steel, these parts securely fasten the dishwasher into place.

Causes relate to normal wear over time from use. Improper original installation may also compromise individual parts. Failing to properly level, brace or anchor the dishwasher leads to unnecessary stresses.

Symptoms of worn or missing installation hardware include:

• Looseness, shaking or movement during operation
• Doors failing to properly self-close or seal fully
• Leaks developing around dishwasher connections
• Installation not compliant with current regulations

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.