Bosch Dishwasher SHP65CM5N Parts

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

If your dishwasher door won't open automatically after cycles, the door opening module may have failed. This electronic assembly controls door operation.

This lock clamp secures an appliance component or assembly so it stays properly seated during operation. Replacing a worn or missing clamp helps restore a stable, rattle-free fit and reliable performance. What it does:

• Holds mating parts together to prevent shifting or vibration
• Helps maintain correct alignment of the secured component
• Can resolve issues where a part won't stay attached or seated
• Restore normal operation when the original clamp is broken or missing

• One lock clamp

• Disconnect power (and shut off water/gas if applicable) before servicing
• Note the clamp's original orientation; take a photo to aid reassembly
• Seat the component fully, then engage the clamp securely without over-stressing it
• Reassemble and test for a firm, stable fit before returning the appliance to service

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

Lower housing that forms the structural base of your dishwasher. Replace when the original case is cracked, warped, or damaged to restore stability.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Replaces a cracked, scratched, or damaged dishwasher inner door panel. Protects internal components and restores the door interior appearance.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Fix loose or rattling dishwasher components with this holder retainer. Secures parts in position to prevent movement and restore quiet operation.

This replacement rack rail restores smooth, stable sliding for a dishwasher rack, helping keep the rack aligned and reduce catching or derailment. It's the straightforward part to repair worn or damaged rack movement. What it does:

• Guides the dishwasher rack along its track so the rack opens and closes smoothly
• Replaces a bent, cracked, or worn rail that can cause the rack to stick or come off track
• Reduces noise and rubbing caused by damaged or misaligned rail components
• Helps maintain proper rack alignment for loading and unloading dishes

• Disconnect power to the appliance before servicing to prevent electrical hazard
• Remove the affected rack and any end caps or clips to access and replace the rail
• Inspect matching rail clips/wheels for wear and replace if needed for proper function

This replacement worm gear is a small plastic drive gear that transmits rotational motion between the motor and driven components, restoring normal gear-driven movement and reducing slipping or grinding. What it does:

• Transfers torque from the motor to the mating gear or gearbox for proper mechanical operation
• Replaces worn, stripped, or damaged worm teeth that cause slipping or loss of drive
• Stops grinding, clicking, or intermittent movement when the gear is the fault
• Helps restore smooth, consistent operation of the driven mechanism when installed correctly

• One worm gear

• Disconnect power to the appliance before beginning any repair
• Inspect mating gears and shafts for wear; replace worn parts to prevent repeat failure
• Use OEM-approved lubricant only where specified; do not force or overtighten mating components

Replacement spring for dishwasher door or latch mechanisms. Restores proper tension and smooth movement when original spring is broken, worn, or missing.

Replacement rack wheel that restores smooth rolling movement to your dishwasher rack. Needed when the original wheel is cracked, worn, broken, or missing.

This outer door front panel replaces a damaged or worn dishwasher door shell to restore the appliance's appearance and proper door cover. It provides the finished exterior surface that protects internal components and accepts trim and handle attachments. What it does

• Replaces a dented, scratched, or rusted outer door surface to improve appearance
• Covers and protects the inner door assembly and control hardware
• Provides mounting points for the handle, trim, and decor panels
• Helps the door close evenly by restoring the exterior door shell

• One outer door (front panel) as pictured

• Disconnect power and water to the appliance before beginning any repair
• Removing the inner door panel may be required to swap outer and inner components; follow OEM instructions
• Use proper fasteners and alignment to avoid gaps or binding when closing the door

Secures internal dishwasher components and keeps assemblies aligned. Replace this mounting clip holder if yours is cracked, broken, or missing.