Bosch Dishwasher SHU5312GB Parts

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

Wax motor for detergent/rinse-aid dispenser.

Fix a dishwasher door that won't close or latch properly. This latch and strike plate assembly restores secure door closure and safe operation.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Connects the sump to the pressure chamber in your dishwasher. Replace if cracked, leaking, age-embrittled, or damaged. Includes 2 o-rings for secure fit.

Replacement front cover for dishwasher control module. Needed when plastic is cracked, broken, or switch actuators are worn or missing. Protects control board.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

This is the cap that seals the rinse-aid dispenser reservoir on the inside of the dishwasher door. It threads or snaps into place to keep rinse aid contained until it is dispensed during the rinse cycle. Replace this cap if rinse aid leaks out prematurely, the cap is cracked or warped, or dishes are coming out spotted due to improper rinse-aid dispensing.

Right side door hinge for dishwashers. Installs on the right side of the door frame. Replace if bent, broken, or damaged from door falling too hard.

Exterior front panel that restores your dishwasher's appearance. Replaces dented, scratched, or corroded panels. Covers and protects inner components.

White on/off button for dishwasher control panel. Replace if button won't stay pressed in, has popped out, or is cracked, broken, or missing from panel.

Pump housing cover for dishwashers. Replaces cracked, broken, or missing covers that protect the pump assembly. Installs over the pump mechanism.