Bosch Dishwasher SHU9902 UC/06 Parts

This rear pump housing is the dishwasher's molded enclosure that supports the drain/pump assembly and channels wash and drain water. Replacing a damaged housing restores proper water flow and helps stop leaks. What it does:

• Houses and aligns the drain/pump components and motor coupling
• Channels water between sump, pump and drain lines to ensure proper draining
• Prevents leaks by sealing the pump assembly area when intact
• Can cause noisy pump operation or failure to drain if cracked or broken

• One rear pump housing

• Disconnect power and turn off water supply before starting; drain any standing water
• Inspect associated seals, gaskets, impeller and mounting hardware; replace if worn
• Handle carefully to avoid damaging mating surfaces; test for leaks after reassembly

Bushing included. To order bushing separately use 00165296. This is the left side hinge. For right side hinge use 00263119.

This is the left side hinge plate. For right side use 00298570.

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This shaft for the float switch is the replacement shaft that secures and guides the dishwasher float to accurately detect water level, helping the appliance fill and shut off properly. Direct-fit design replaces the worn or broken float shaft. What it does

• Guides the float so the level-sensing switch can detect low or high water levels.
• Prevents overfilling by ensuring the float actuates the water-level switch reliably.
• Commonly replaces a cracked, bent or missing shaft that causes inconsistent fill, continuous filling, or water-level errors.

• One replacement float switch shaft.

• Disconnect power to the appliance before starting any repair.
• Remove the access panels and float assembly per your model's service instructions to reach the shaft.
• Inspect the float and switch for damage; replace only the failed components as needed.
• Reassemble carefully and test fill/stop operation before returning the appliance to service.

This is the front corner block. For rear corner block use 00263093.

This replacement silverware basket holds forks, knives and spoons so utensils stay organized and clean during the dishwasher cycle. It restores a convenient, secure place for cutlery and helps prevent nesting for better wash coverage. What it does:

• Holds and separates silverware to improve cleaning and prevent items from nesting
• Provides a removable container that stays in place during wash cycles
• Fits into the lower rack to keep utensils contained and easy to unload
• Helps protect small items from falling to the tub or blocking the spray arm

• No tools typically required; slides or snaps into the lower rack location
• Remove all dishes and power off/dry area before installing to avoid injury
• Inspect rack tines and basket clips for damage; replace if broken to ensure proper fit

This is the rear corner block. For front corner block use 00263094.

The Lower Dishrack Assembly is an OEM part for Bosch dishwashers. This assembly holds the dishes, utensils, and other items to be cleaned on the lower level of the dishwasher. It is designed to slide in and out smoothly, providing easy access for loading and unloading.

Over time, the lower dishrack can become worn out or damaged due to frequent use, exposure to high temperatures, and the weight of the items placed on it. Causes of a bad lower dishrack include broken or missing wheels, rust, and damage to the rack's frame or coating.

Symptoms of a bad lower dishrack include:

• Difficulty sliding the rack in and out
• Rust or corrosion on the rack
• Broken or missing tines
• Items not staying in place during the wash cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle