Bosch Dishwasher SHU9902 UC/06 Parts

This O-ring is the sealing gasket between mating components, keeping fluid contained inside the system. Replacing a worn ring restores a tight, leak-free connection and helps prevent drips, moisture, and leak-related error indications.

• Creates a compressible seal between parts to prevent leaks at the joint
• Helps maintain proper system flow by stopping seepage or air ingress
• Direct replacement for rings that are flattened, cracked, brittle, swollen, or missing
• Common symptoms include dripping at the connection, moisture beneath the unit, or leak/float error alerts

• Disconnect power and shut off the water supply before servicing; wear appropriate PPE.
• Note the original ring's location; clean the groove and mating surfaces before installation.
• Apply a light coat of compatible silicone grease; avoid twisting or overstretching the ring.
• Seat evenly, reassemble, restore service, and check for leaks during a test cycle.

The Water Inlet System is an OEM component specifically designed for select Bosch dishwashers. Comprising inlet valve, screens, hoses, and connectors, it precisely meters fresh water. Reliable flow prevents mineral buildups from impairing performance.

Causes of a bad water inlet system commonly involve bursting hoses or stripped connectors. Prolonged pressure weakens seals requiring timely replacement.

Symptoms of a faulty water inlet system include: 

- Fluctuating or absent water flow to spray arms
- Leaks forming inside or near the installation site
- Errors relating to improper water temperature or amounts  

Causes of a bad water inlet system involve typical degradation such as:

• Limescale clogging narrow valve openings
• Plumbing joint corrosion compromising integrity
• Splitting plastic tubing unable to withstand cycles

This OEM Bosch part is also compatible with some Miele, Blomberg, and Thermador dishwashers. 
 

The Screw is an OEM replacement part for Bosch dishwashers. Hundreds of screws hold the appliance panels and internal mechanisms securely in place. Consistent, protective enclosures ensure long-lasting performance.

Causes of a bad screw can include stripped threads from repeated tightening/loosening during repairs. Corrosion posing integrity risks may develop if water penetrates screw heads over time. 

Symptoms of a bad screw include: 

• Panels or racks that rattle or come loose during operation
• Gaps appear that allow residual moisture to seep within
• Internal components shifting position from the original assembly
• Loose wiring susceptible to abrasion posing electrical hazards

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

Includes door latch, strike plate and microswitch.

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Color: gray. Each clip measures about an inch and each pack includes 2 clips.

This actuator arm is the mechanical lever inside the dishwasher door's dispenser assembly. Working with its spring, it releases the detergent cup at the proper point in the cycle to restore consistent detergent dispensing. What it does

• Transfers motion from the control/drive mechanism to the dispenser latch to open the detergent cup
• Provides the spring tension needed for the lever to return to its home position
• Helps ensure detergent is dispensed at the intended time in the wash cycle
• Common symptoms include detergent left in the cup, a dispenser door that won't latch or opens inconsistently, or a visibly broken/missing lever

• 1 actuator arm with spring

• Disconnect power to the dishwasher before servicing
• Open the door and remove the inner door panel fasteners to access the dispenser linkage
• Note the spring orientation; move the spring to the new arm if needed and seat the arm in the correct pivot location
• Reassemble the door and manually test the dispenser action before running a cycle

Wax motor for detergent/rinse-aid dispenser.

Tall item spray head.
This Spray Head is an OEM part for Bosch Dishwashers. It plays a role in distributing water evenly during the dishwasher's washing cycles. Continuous exposure to hard water, debris, or mineral deposits can cause issues with this component.

What Causes a Bad Spray Head:
Hard water deposits, debris, or mineral buildup can clog or block the spray head, affecting its performance. Physical damage can also impair its functionality.

Symptoms of a Bad Spray Head:

• Inadequate cleaning of dishes
• Uneven water distribution
• Reduced water pressure during washing cycles

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.
 

This drain hose adapter connects the appliance's drain hose to another hose or a compatible fitting, providing a secure, leak-resistant joint so wastewater can be routed to the household drain. Replace when the original adapter is cracked or loose.

• Couples the drain hose to another hose or to a sink/disposal/standpipe fitting
• Helps seal the joint to reduce leaks and hose slippage
• Restores a tight fit when the original adapter is worn, brittle, or missing
• Symptoms of a bad adapter: leaking at the connection, hose won't stay attached, visible cracks

• Disconnect power and turn off water before servicing
• Place a towel or pan to catch residual water from the hose
• Fully seat hose ends over the adapter barbs and secure with appropriate hose clamps
• Run a short test cycle and inspect all connections for leaks

This O-ring seals the NTC (negative temperature coefficient) temperature sensor where it inserts into the appliance. It restores a watertight seal at the sensor port to help prevent leaks and maintain reliable temperature-sensing performance.

• Provides a leak-tight seal between the NTC temperature sensor and its housing/tub/sump
• Helps prevent water seepage and moisture intrusion around the sensor opening
• Common symptoms of a failed seal: drips near the base, moisture in the leak tray, flattened/cracked ring, or a sensor that feels loose
• Good practice to replace when the NTC sensor is removed for service

• Disconnect power and shut off water supply before servicing
• Access the NTC sensor, remove the old O-ring, and clean mating surfaces
• Lightly moisten the new O-ring with water; seat it evenly to avoid pinching, then reinstall the sensor fully
• Run a brief test cycle and inspect for leaks

This O-ring is a circular sealing gasket that creates a watertight joint between mating parts. Replacing a flattened or cracked ring restores a tight seal and helps prevent leaks during operation.

• Provides a compressible seal between fittings, hoses, or housings
• Helps prevent drips and leaks at joints under normal system pressure
• Maintains proper flow by keeping connections sealed
• Typical failure signs: visible cracking/flattening, seepage at a joint, pooling water near the appliance

• Disconnect power and shut off the water supply before servicing
• Relieve any line pressure and place a towel to catch residual water
• Clean and inspect mating surfaces; replace any damaged components
• Lightly lubricate the O-ring with approved silicone lubricant, seat evenly without twisting, and test for leaks after reassembly

This replacement foot is the leveling support at the base of your appliance. It helps set the height and keep the unit stable and level, reducing wobble, vibration, and noise for smoother, quieter operation.

• Supports the appliance base and provides solid floor contact
• Allows height/leveling adjustment as designed by the unit
• Helps correct rocking, vibration, walking, or door misalignment caused by an unlevel appliance
• Replace if the foot is cracked, missing, worn, or stripped and won't hold adjustment

• Disconnect power; shut off water supply if applicable
• Protect flooring and have a helper steady or move the unit
• Remove the damaged foot; install the new foot per the mounting style (threaded or push-in)
• Adjust height to level the cabinet and stability at all corners

This genuine OEM part is a circulation pump motor for dishwashers. The circulation pump motor distributes water to the spray arm to allow the dishwasher to properly do its job. Over time, the circulation pump motor can become overworked to the point of becoming inoperable. Luckily, replacing the pump motor is not as difficult a job as it might seem. To begin the repair, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the circulation pump and align the pump with the seal and sump. Tighten the clamp and transfer the wires from the old pump to the new one. Proceed to reinstall the panels that were uninstalled.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dishwashers.

This is the right side hinge plate. For left side use 00298567.