Bosch Dishwasher SHV53E13EU Parts

Leaking water around the inlet valve? This rubber inlet seal creates a watertight connection at your dishwasher's water inlet to stop drips and leaks.

Upper rack crockery basket insert for dishwashers. Holds plates, bowls, and small dishware securely in the top rack. Replace if cracked or missing.

Fix corrosion or electrical issues caused by water damage. This moisture shield protects internal components from condensation. Simple DIY repair.

Securing kit for dishwasher installation. Includes mounting hardware to attach your dishwasher to cabinetry. Replace if brackets are missing or damaged.

This is a trim strip used on the dishwasher to provide a finished edge or seal along a panel surface. It helps cover gaps and gives the appliance a clean, polished appearance. Replace this strip if it is cracked, broken, missing, or no longer staying in place, which can affect the look of the dishwasher or allow moisture to reach areas it shouldn't.

This is a mounting holder used inside a dishwasher to secure and support internal components in their proper position. It helps keep parts aligned during the wash and drain cycles. Replace this holder if it is cracked, broken, or missing, which can cause loose or misaligned parts and unusual noises during operation.

Dishwasher salt funnel guides water softener salt into the reservoir without spills. Replace if cracked or lost to maintain proper salt loading.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Connects the sump to the pressure chamber in your dishwasher. Replace if cracked, leaking, age-embrittled, or damaged. Includes 2 o-rings for secure fit.

Replacement spray arm assembly that installs in the dishwasher tub to restore water distribution. Needed when the original is cracked, worn, or missing.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers. 

This tube channels water from the inlet valve to the wash system inside the dishwasher. It ensures a steady supply of water reaches the spray arms for proper cleaning during wash and rinse cycles. Replace if the tube is cracked, kinked, or leaking, which can cause poor water flow, inadequate cleaning, or water pooling under the dishwasher.

Secures wooden or custom exterior panels to your dishwasher door. Replace if your panel rattles, shifts, or feels loose. Confirm fit with your model.