Bosch Dishwasher SHV88PW53N Parts

Replacement screw for securing dishwasher panels, trim pieces, and brackets. Restores proper fit when original screws are stripped, lost, or damaged.

Insulating strip shields dishwasher wiring from heat and abrasion. Replace if frayed, brittle, or damaged to prevent electrical hazards. Confirm fit.

Replace your dishwasher's detergent dispenser lid if it's cracked, broken, or missing. This cover snaps onto the dispenser to keep detergent secure.

Fix dishwasher electrical issues with this cable harness. Resolves control panel malfunctions, display errors, and power connection problems.

Dishwasher repair set includes essential components for maintenance and fixes. Replace when parts show wear or damage. Verify fit with your model number.

This micro filter is a fine-mesh replacement filter that traps food particles and debris in the dishwasher sump, helping maintain wash performance and protect the pump and drain from clogs. What it does:

• Captures small food particles to prevent recirculation and reduce spotting
• Helps keep the dishwasher drain and pump from clogging
• Supports consistent water flow for better cleaning results
• Can reduce odors caused by trapped debris in the filter area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack to access the sump area; follow your owner's manual for filter removal
• Ensure the filter is properly seated and locked before running a cycle
• Clean surrounding areas and inspect for additional debris while replacing the filter

This insulating part provides a non-conductive, heat-resistant barrier between adjacent components inside the appliance. Replacing a damaged insulator helps prevent unintended contact and heat transfer, supporting safe, reliable operation and protecting nearby parts. What it does:

• Electrically isolates terminals or metal surfaces to help prevent shorts or arcing
• Reduces heat transfer to surrounding components
• Maintains proper spacing and support for the protected component
• Replace if the original is cracked, deformed, missing, or shows burn/discoloration

• 1 insulating part

• Disconnect power before servicing; shut off gas or water if applicable
• Access the component, note orientation/positioning of the original insulator, and transfer any clips or hardware as required
• Seat the new insulator fully and ensure no conductive parts touch unintended surfaces
• Reassemble, restore power, and verify normal operation with no rubbing, arcing, or overheating

Dishwasher making unusual noise or components overheating? This insulation shield acts as a thermal and electrical barrier, protecting wiring and reducing vibration contact. Simple DIY fix.

Fix intermittent power or signal issues in your dishwasher with this internal connection cable. Restores electrical connection between components.

This insulating part is a small thermal/electrical insulator used on select appliances to help prevent heat transfer and protect nearby components. It reduces heat-related wear and helps maintain safe operation around sensitive parts. What it does:

• Provides thermal insulation between hot components and adjacent parts to reduce heat transfer.
• Helps protect wiring, plastic components, and electronics from overheating.
• Can prevent heat-related noise, discoloration, or softening of nearby materials.
• Useful when replacing damaged, brittle, or missing insulation that exposes components.

• One insulating part as shown

• High-level replacement only; ensure appliance is unplugged or power is disconnected before service.
• Handle carefully to avoid contamination or damage; install in the same orientation and location as the original.
• If insulation is attached near high-temperature components, verify surrounding parts are intact and not degraded.

This operating module is the appliance control interface that routes user commands to the main control board, restoring keypad/console response and cycle selection. Replaces a failed or unresponsive control module to return normal panel operation. What it does:

• Receives inputs from the console and sends control signals to the main control board
• Restores responsive buttons, cycle selection, and user interface feedback
• Helps resolve symptoms like unresponsive controls, missing cycle selection, or intermittent panel behavior
• Does not include user-facing trim or external buttons unless listed separately

• One operating module

• High-level: disconnect power before servicing to avoid shock or board damage
• Handle the module by its edges and avoid static discharge; use an anti-static wrist strap if available
• Replace only if diagnostics indicate a faulty control module; verify connectors and wiring before swap