Bosch Dishwasher SHX36L06UC Parts

Traps food debris and particles in your dishwasher sump. Replace when clogged with hard water deposits or buildup affects cleaning. Verify fit by model.

Replacement silverware basket with handle for dishwasher lower rack. Holds utensils upright for better cleaning. Replaces cracked, broken, or missing baskets.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Light gray flip tine latch for dishwasher dishrack. Replaces broken, cracked, or missing latches that secure flip-down tines in upper or lower racks.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

Drain hose clamp

Replace your dishwasher's upper rack rail if cracked, broken, or worn. This guide rail installs along the sides to support smooth rack sliding.

Fix dishes not drying or cycles taking 3+ hours. This heating element heats wash water and enables drying. Moderate DIY repair with video guide.

The Cabinet Side Seals are an OEM part for Bosch dishwashers. These seals are located along the sides of the dishwasher cabinet and play a crucial role in preventing water leaks and maintaining an airtight seal during operation.

Causes of a bad seal can include general wear and tear over time, exposure to high temperatures or moisture, or damage from mishandling or improper installation.

Symptoms of a bad Cabinet Side Seal include:

• Water leaks or moisture buildup around the sides of the dishwasher
• Difficulty closing the dishwasher door properly
• Decreased efficiency in drying performance
• Potential for water damage to surrounding areas

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.