Bosch Dishwasher SHX84AYD5N Parts

The Divertor Motor is an OEM part for Bosch dishwashers.  This part controls the direction of water flow within the unit. This motor directs the water to different spray arms based on the selected wash cycle, ensuring efficient cleaning by optimizing water usage and spray intensity. 

Causes of damage to the divertor motor can include regular wear and tear, exposure to water and detergent over time, and electrical issues such as wiring problems or faults in the control board.

Symptoms of a failing Divertor Motor include:

• Inadequate water distribution during cycles, which can lead to uneven cleaning results.
• The dishwasher making unusual noises, such as humming or grinding, which may indicate a struggle in the motor function.
• Certain wash zones receiving little to no water, affecting the appliance's overall performance.
• Error codes displayed on the dishwasher panel that relate to water circulation problems.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Secures panels, brackets, and internal components in your dishwasher. Replace this screw if it's stripped, missing, or corroded to restore proper fit.

Replace your dishwasher's thermal insulation if experiencing excessive heat around the unit or noise during cycles. Protective barrier for safer operation.

Vent hose for dishwashers that guides steam and moisture out during wash cycles. Replace if cracked, disconnected, or worn to restore proper venting.

The Spray Head is an OEM replacement part for Bosch dishwashers. It directs pressurized water along the dish racks, targeting every inch of dishware and cookware. Consistent coverage cleans thoroughly without waste.   

Symptoms of a bad spray head can include clogged nozzles, inconsistent patterns, or spray heads that do not oscillate and rotate properly through cycles. Mineral deposits pose blockage risks over time.

Causes of a bad spray head include:

• Uneven or skipped areas of spray coverage inside the machine
• Rotating/oscillating mechanisms that jam or continuously stick  
• Nozzles fully or partially blocked reducing water pressure
• Head assembly detaching from water tub wall or bracket

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.

• Secures panels, brackets, or internal components as specified by the manufacturer
• Helps maintain proper alignment and reduces vibration or rattling
• Replace if the head is stripped, threads are damaged, or the screw is missing
• Common signs include loose or misaligned panels/trim and hardware that won't stay tight

• Disconnect power and turn off water or gas supply as applicable before servicing
• Match length and thread to the original; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly without overtightening
• Retain any original washers, bushings, or clips used in the assembly

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Replaces a cracked, scratched, or damaged dishwasher inner door panel. Protects internal components and restores the door interior appearance.

Factory mounting screw secures panels, brackets, and internal components in your dishwasher. Replace missing, stripped, or damaged screws during repair.

Replacement dishwasher housing cabinet that restores the outer enclosure. Needed when the original is cracked, broken, or damaged, compromising stability.

This outer door front panel replaces a damaged or worn dishwasher door exterior to restore appearance and protect internal door components. It provides the visible finish and mounting surface for trim, handles, and latch hardware. What it does:

• Restores the dishwasher's exterior finish and hides internal components
• Provides mounting surface for handle, trim, and latch assemblies
• Helps maintain door alignment and a proper seal when installed correctly
• Replaces panels that are dented, cracked, scratched, rusted, or cosmetically worn

• Disconnect power and water to the appliance before beginning any repair
• Support the door during removal to avoid damaging hinges or wiring
• Remove and transfer any trim, handle, latch, and insulation exactly as removed
• Adjust hinge positioning if needed for a proper seal