Bosch Dryer WTA3510US Parts

Dryer not heating or overheating? This high-limit thermostat cuts power when temperatures exceed safe levels. Common fix for no heat issues.

Replace your dryer's lint filter to maintain proper airflow and drying efficiency. Install when torn, clogged, or damaged. Confirm fit with model number.

Connects your dryer exhaust to the vent hose for proper airflow. Replace if cracked, broken, or damaged from wear or improper installation.

A 15 amp cartridge fuse that protects appliance electrical circuits from overcurrent, helping prevent damage to controls and components. Fits into inline fuse holders or boards where that specific fuse rating is required. What it does

• Interrupts circuit power when current exceeds 15 amps to protect wiring and electronics
• Commonly linked to symptoms like no power to controls, unresponsive display, or appliances that won't start
• Designed to be replaced when visibly blown or when continuity test fails
• Works as the exact rated safety fuse specified for compatible appliances

• One 15 amp cartridge fuse

• Disconnect all power to the appliance before accessing or replacing the fuse
• Replace with the identical fuse type and 15 amp rating only; do not substitute different ratings
• Handle carefully and mount fully seated in its holder or on the PCB as designed
• If the new fuse fails again immediately, stop — repeated failures indicate underlying electrical faults

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

Fix intermittent dryer operation or complete loss of function with this wire lead cable. Restores electrical connections between controls and components.

This is a protective cover used on the dryer to shield an internal component or opening. It helps keep debris out and ensures safe, proper operation of the area it encloses. Replace this cover if it is cracked, broken, or missing, which could expose internal parts or affect dryer performance.

Dryer door seal creates an airtight barrier to retain heat and improve efficiency. Replace if torn, cracked, or causing heat loss. Verify fit with your model.

Dryer turns on but won't start? A faulty door latch prevents the cycle from beginning. This mechanism secures the door and completes the circuit.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

Drum support plate for dryers. Mounts beneath the drum to provide structural support. Replace if cracked, warped, or causing alignment issues.