Bosch Dryer WTE8630XTR Parts

This hose connection inlet provides the sealed connection point where the appliance's water inlet hose mates to the valve or tub, restoring a leak-free water feed and reliable flow for normal operation. What it does

• Connects the inlet water hose to the appliance inlet fitting or valve, directing water into the unit
• Creates a sealed joint to prevent drips and leaks at the hose connection
• Replaces cracked, worn, or damaged fittings that can cause visible leaks or reduced water flow
• Helps resolve symptoms such as water pooling under the appliance, continuous dripping, or inlet hose not seating properly

• One hose connection inlet

• Always disconnect power and shut off the water supply before starting work
• Inspect and replace any worn O-rings, gaskets, or clamps when installing this fitting
• Hand-start threads, then tighten clamps or fasteners to secure the hose; avoid over-tightening plastic parts
• After installation, restore water and power and check carefully for leaks during a short test cycle

Replace your dryer door seal to stop air leaks and improve drying efficiency. Install when you notice tears, gaps, or lint escaping. Verify fit with your model.

Structural holder component for dryers. Secures internal parts in proper position. Replace if broken, cracked, or missing to restore proper fit.

This is a translucent cover that protects the drum light bulb inside the dryer. It snaps into place over the light assembly to shield the bulb from clothing and tumbling items while allowing light to illuminate the drum interior. Replace this cover if it is cracked, missing, or yellowed, which can leave the bulb exposed to damage or reduce visibility inside the drum.

Appliance overheating or won't run? This thermal cutoff opens the circuit at unsafe temperatures to protect your unit. Simple replacement restores safety.

If your dryer isn't drying efficiently or has moisture buildup, the air channel may need replacement. Guides airflow for proper venting and performance.

This is the fan drum (blower wheel) that attaches to the motor shaft inside the dryer. It circulates heated air through the drum to dry clothes efficiently. Replace this part if your dryer is making unusual rattling or squealing noises, takes too long to dry clothes, or produces weak airflow from the exhaust vent.

Replace your dryer's duct if cracked, damaged, or missing. This duct channels air through the system for proper ventilation and efficient drying performance.

This is a dishwasher drain pump assembly that removes standing water from the tub so cycles can finish and dishes can drain properly. Direct-fit replacement for affected drain systems. What it does:

• Pumps wastewater from the dishwasher to the household drain during drain cycles
• Restores normal draining when a failed pump leaves water in the tub
• May correct symptoms such as standing water, cycle failures, or unusual pump noise
• Works with the dishwasher's drain hose and check valve to prevent backflow

• Disconnect electrical power and water supply before starting any repair.
• Confirm compatibility using your appliance model number; inspect seals and hose connections during replacement.
• Handle the impeller and motor housing carefully; avoid crushing wiring or connectors.
• Run a short test cycle and check for leaks after installation.

Dryer door hinge provides the pivot point for smooth opening and closing. Replace if hinge is cracked, broken, worn from repeated use, or missing.

This high-temperature 220V, 15-watt oven light bulb restores bright interior lighting so you can monitor cooking progress without opening the door. It's built for sustained heat and replaces a burned-out or flickering lamp.

• Illuminates the oven cavity during baking, broiling, and cleaning cycles
• High-temperature design for continuous heat exposure
• Common failure symptoms: no light when switched on, dim or intermittent illumination, blackened glass, or a broken filament

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/cover; unthread and remove the old bulb
• Thread in the new bulb of the same voltage and wattage; do not overtighten
• Reinstall the cover, restore power, and test the light

Fix a dryer making loud noises or not tumbling with a new drum. This part holds clothes during the drying cycle and may rust, dent, or crack over time.