Kenmore Refrigerator 106.50212010 (10650212010, 106 50212010) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking water filter housing and broken grill cover clips Carl H. • Strongsville , OH • December 04, 2016
Ordered parts, watched the videos on your website. Very simple.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196483
The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.
Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.
Symptoms of a bad shelf stud include:
- Shelves not staying securely in place
- Shelves tilting or collapsing
- Visible cracks or damage to the stud
- Difficulty in inserting or removing shelves
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.
Do-It-Yourself Stories from Customers like You
Broken shelf and drawer. Regina M. • Yardley , PA • November 10, 2017
Myself
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10304659
Note: Right Hand Roller
Do-It-Yourself Stories from Customers like You
Rollers under refrigerator were worn and/or broken Tim C. • Pasadena , MD • February 28, 2020
Lifted refrigerator in front and back. Removed roller pin holding assembly. Removed defective assembly and replaced with new.
Read more
More
$55.37
- Compare At:
-
$66.44
- You Save:
-
$11.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2206671W
Color: white. Measures about 9 inches wide by 2-1/2 inches deep.
Do-It-Yourself Stories from Customers like You
Broken dispenser lever retainer ice guide and overflow grille Tony R. • Milford , DE • May 23, 2015
I watched the videos and made the repairs in a little over 5 minutes! It was great and if I ever need parts again I was use this site. I have told everybody about this site.
Read more
More
$51.27
- Compare At:
-
$61.52
- You Save:
-
$10.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10304660
Note: Left Hand Roller
Do-It-Yourself Stories from Customers like You
Rollers under refrigerator were worn and/or broken Tim C. • Pasadena , MD • February 28, 2020
Lifted refrigerator in front and back. Removed roller pin holding assembly. Removed defective assembly and replaced with new.
Read more
More
$55.37
- Compare At:
-
$65.89
- You Save:
-
$10.52
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2174706
This small pin clip secures the roller pin in a refrigerator drawer/track assembly, keeping the roller and pin from sliding apart. Replacing a missing or bent clip restores smooth drawer movement and helps prevent bins from tilting, binding, or dropping.
- Retains the roller on its pin to keep the drawer track assembly together
- Helps resolve drawers that tilt, bind, or fall when a clip is missing or damaged
- Prevents the pin from backing out, reducing scraping or popping noises
- Replaces clips that are missing, bent, or no longer hold securely
What's included: 1 clip Install notes:
- Disconnect power and remove the drawer/bin to access the track and roller
- Support the roller; remove the old clip with small pliers while securing the pin
- Align roller and pin; press the new clip fully into the groove until seated
- Reassemble and verify the drawer glides smoothly without binding
Do-It-Yourself Stories from Customers like You
Rear refrigerator wheel fell off Cyndie W. • Otsego , MN • June 03, 2019
Watched the repair video which was posted with the part. The clip was a little hard to get on because it needs to be tight on the pin, but I was finally able to push it in place. It was a quick fix and now the refrigerator is level.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2309758
This freezer bin replaces a cracked or missing bin to restore organized storage in your freezer. It mounts on existing tabs or rails to keep frozen items secure and easy to access.
- Provides storage and organization within the freezer compartment
- Replaces a broken, warped, or missing bin
- Helps prevent items from tipping or falling when the door opens
- Restores proper fit so the bin stays seated on its mounts
What's included: One freezer bin. Install notes:
- Power isn't required for this replacement; open the freezer and remove items from the affected area
- Lift the old bin straight up and out from the tabs/rails
- Align the new bin with the mounting points and slide or press down until fully seated
- Do not force into place; distribute weight evenly and avoid overloading
Do-It-Yourself Stories from Customers like You
Bin freezer broken Arthur H. • Miami , FL • May 16, 2016
I found the correct part and oredered. It was really great to receive that by next day in and I installed it.
I would recommend and use myself ApplianceParts Pro any time.
Arthur Hem
Read more
More
$73.95
- Compare At:
-
$88.00
- You Save:
-
$14.05
Genuine Whirlpool part
By: Whirlpool
Part Number: W10122561
This icemaker fill cup guides incoming water from the refrigerator's inlet tube into the ice mold, helping prevent splashing and freeze-ups during the fill cycle. Replacing a cracked or missing cup restores consistent fills and reduces leaks.
- Directs water from the fill tube straight into the icemaker mold
- Helps prevent overspray, splashing, and ice buildup around the icemaker
- Replace if the cup is cracked, warped, loose, or missing
- Common symptoms: water dripping/freezing under the icemaker, clumped or misshapen cubes
What's included: 1 fill cup Install notes:
- Unplug the refrigerator and turn off the water supply before servicing
- Remove the icemaker assembly as needed to access the inlet/fill area
- Release the old cup and seat the new cup so the fill tube aligns with the opening
- Restore water and power; check for proper fill and any leaks
Do-It-Yourself Stories from Customers like You
Broken parts Miguel D. • Miami , FL • October 24, 2016
I SAW THE VIDEO AND WAS SO EASY THAT MY CHILDREN COULD DO IT
Read more
More
$18.47
- Compare At:
-
$21.98
- You Save:
-
$3.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10143759
Do-It-Yourself Stories from Customers like You
Failed to cool due to hole/s in evaporator leaking freon Gerald L. • Myrtle Beach , SC • August 17, 2017
Ordered new Evaporator part and Drier from Appliance Pros. The part arrived earlier than expected and was properly packaged. I had both parts installed by a professional as they required a level of expertise above my capabilities. Works perfectly.
Read more
More
$28.23
- Compare At:
-
$33.59
- You Save:
-
$5.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3196557
This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.
- Fastens brackets, panels, trim, or components to the appliance chassis
- Helps correct loose or missing hardware after vibration or service
- Replaces stripped, rusted, or broken screws
- Can reduce rattling noises or misaligned parts caused by missing fasteners
What's included: One screw Install notes:
- Disconnect power; for gas appliances, also shut off the gas supply
- Support the part being fastened; start threads by hand to avoid cross-threading
- Use the correct driver size; tighten snugly without overtightening
- Replace hardware with the exact part number to ensure proper fit
Do-It-Yourself Stories from Customers like You
Water dispenser was no longer working Kelly W. • Houston , TX • January 24, 2017
After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10122563
This comb-shaped insert mounts at the front of the modular ice maker. It strips freshly ejected cubes from the rake and directs them into the bin to help prevent jams and cube hang-ups for consistent ice harvests.
- Guides cubes off the ejector fingers and into the bin
- Helps prevent cubes from re-entering the mold, bridging, or jamming
- Replaces a cracked, warped, or missing stripper to restore proper harvest path
- Typical symptoms: cubes stuck on the ejector, repeated jams, ice spilling or clumping
What's included: 1 ice stripper Installation notes:
- Disconnect power to the refrigerator and turn off the ice maker before servicing
- Remove the ice maker front cover; release locking tabs or screws to remove the old stripper
- Position the new stripper over the ejector fingers; seat fully without forcing the rake
- Reinstall cover/ice maker, restore power, and allow a full cycle to verify operation
Do-It-Yourself Stories from Customers like You
Piece broken on the icemaker Gerald H. • Kansas City , MO • February 17, 2020
Removed icemaker and inserted the part
Read more
More
$51.29
- Compare At:
-
$61.04
- You Save:
-
$9.75