Kenmore Refrigerator 106.50272010 (10650272010, 106 50272010) Parts

Size: 1/4 inch.

The ice maker bracket is an OEM part for Whirlpool refrigerators. This bracket is a structural component that holds and supports the icemaker assembly within the refrigerator. It allows for secure mounting and installation of the icemaker while also maintaining proper alignment.

Causes of a bad bracket can include wear and tear over time, cracks or breaks due to impact or stress, or corrosion issues that compromise the integrity of the mounting structure.

Symptoms of a bad bracket include:

• Loose or unstable icemaker installation
• Improper ice production or dispensing
• Noise or vibrations emanating from the icemaker area
• Moisture leaks or water damage near the bracket mounting points

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

This replacement ice door is the dispenser flap that opens and closes to release ice from the freezer into the dispenser chute, restoring normal ice delivery and helping keep the dispenser sealed when idle. What it does:

• Replaces a cracked, warped, or broken dispenser/ice door that won't open or close properly
• Helps stop ice from jamming or falling into the dispenser area
• Restores the seal that keeps warm air out of the ice chute
• Works with the dispenser actuator to allow normal ice dispensing

• Disconnect power to the refrigerator before starting any work.
• Remove the dispenser housing trim per your model's service instructions to access the door; handle carefully to avoid damaging surrounding components.
• Inspect the actuator arm and mounting tabs during install; replace or realign if worn or broken.
• Test dispenser operation after installation to ensure the door opens and closes smoothly.

This blade mounting block secures the blade assembly to the appliance, keeping cutting or stirring components aligned for reliable operation and reduced vibration. It restores proper blade positioning to help eliminate noise and uneven performance. What it does:

• Supports and locates the blade assembly so blades stay aligned during operation
• Prevents wobbling or contact that can cause noise and premature wear
• Helps restore consistent cutting/stirring action when a loose or damaged block is present
• Common symptom: loose blade, rattling or grinding noises, or uneven operation

• One blade mounting block

• Disconnect power (and water if applicable) before beginning any repair
• Remove blade assembly per OEM instructions to access and replace the block
• Inspect surrounding components (fasteners, blades, seals) for wear and replace as needed

Includes both right and left hand sides.

The Wire Harness is an OEM part for Whirlpool refrigerators. It provides the electrical connection between various parts of the refrigerator, ensuring proper communication and voltage.

A bad wire harness can occur due to wear and tear, electrical malfunctions, or damage to the wiring itself. If you notice symptoms such as the refrigerator not cooling properly, erratic behavior, or error codes displayed on the control panel, it may be time to replace the wire harness.

Symptoms of a bad wire harness include:

• Inconsistent cooling or inadequate temperature control
• Erratic behavior or unusual noises coming from the refrigerator
• Error codes displayed on the control panel

Repair your refrigerator by replacing the faulty or damaged wire harness with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.