Kenmore Refrigerator 106.51149110 (10651149110, 106 51149110) Parts

This flipper spring returns the refrigerator's ice dispenser door (chute flapper) to the closed position after dispensing. It helps keep warm air and moisture out to minimize frost at the chute and reduce ice clumping in the bin.

• Provides the closing tension for the ice chute door/flapper
• Helps maintain a proper seal at the dispenser opening
• If worn or broken, you may notice the flapper not closing fully
• Frost/condensation around the chute or ice clumping in the bucket may occur

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control to access the ice chute door assembly; note spring orientation and anchor points
• Install the new spring in the same orientation; the flapper moves freely and closes under spring tension
• Wear gloves and use caution—metal edges in the dispenser area can be sharp

The Wire Harness is an OEM part for Whirlpool-brand side-by-side refrigerators. It facilitates connection between many internal control boards and components.  

Symptoms of a bad wire harness include:

• Faulty or intermittent operation of light fixtures   
• Error codes displayed for no reason
• Random component failures or malfunctions
• Buzzing noises emitting from electrical areas

As the connection backbone inside refrigerators, wire harnesses endure years of constant vibration and flexing from icemakers and cooling fans. Causes of failure are typically cracks developing in older insulation from normal wear.

Compatible also with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore side-by-side models. Do not cut or shorten any wires without verifying the wire function first.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This door hinge supports and pivots the appliance door so it opens smoothly and closes flush. Replacing a worn hinge helps restore proper alignment and sealing for consistent performance and safe operation. What it does:

• Provides the pivot point and support for the door
• Helps maintain door alignment and proper seal/latch engagement
• Controls opening/closing action (spring-tensioned on many models)
• Common symptoms: door won't close fully or pops open, door sags or rubs, drops too quickly, squeaks/binds when moving

• 1 door hinge

• Disconnect power (and shut off gas, if applicable). Allow the unit to cool before servicing.
• Support the door; hinges may be under spring tension—use hinge locks/pins as designed and keep hands clear of the mechanism.
• Remove mounting screws, transfer any screws/brackets from the old hinge, and seat the new hinge fully in the receiver.
• Replacing both sides together often ensures even alignment and proper closure. Verify door operation and seal after reassembly.

This cam door replaces the small plastic cam that guides and supports the appliance door mechanism, restoring proper door alignment and secure closing so the appliance can latch and operate reliably. What it does:

• Guides the door or door strike into the correct position during closing
• Helps the latch engage so the appliance recognizes the door as closed
• Replaces worn, cracked, or broken cams that cause misalignment or noisy operation
• Can stop symptoms such as a door that won't seat, rattles when closing, or prevents the appliance from starting

• One cam door (single replacement cam)

• Disconnect power (and water if applicable) before starting any repair
• Remove the door or access panel per your model's service instructions to reach the cam
• Verify cam orientation and engagement with the latch/strike before final assembly

Replacement bracket that secures and supports internal components, restoring firm mounting and reducing rattling. Replaces a worn or damaged bracket to help keep appliance parts aligned for quieter, more reliable operation. What it does:

• Provides a stable mounting point to hold internal components in place
• Reduces rattling, vibration, and misalignment caused by a loose or damaged bracket
• Restores proper component spacing to help prevent contact and wear
• Works as a direct replacement for a failed bracket to return proper function

• Disconnect the appliance from power (and water, if applicable) before servicing
• Handle edges carefully; wear gloves to avoid cuts during removal/installation
• Reuse existing fasteners unless new hardware is specified; ensure bracket is securely tightened and component alignment is checked

This multi-connector wire harness routes power and signals between appliance components to restore reliable electrical connections. Replace a damaged harness to fix intermittent operation or loss of function caused by broken wires, melted insulation, or loose plugs. What it does:

• Carries power and control signals between the control board and connected components
• Re-establishes electrical continuity when wires are frayed, broken, or connectors are corroded
• Helps stop intermittent operation, component failures, or no-power symptoms tied to wiring faults
• Prevents arcing or shorts caused by damaged insulation or loose connections

• One complete wire harness assembly as shown

• Disconnect all power (unplug or switch off breaker) before starting any repair
• Compare the new harness to the old one; route and secure wires the same way to avoid pinching
• Use care with connectors—align and seat plugs fully until they click
• If you see damage to surrounding components, inspect and replace those parts as needed

This cover corner replaces a missing or damaged corner trim piece to restore the refrigerator's interior/exterior finish and help keep shelves and bins seated properly. It provides a clean, finished look and protects edges from wear. What it does:

• Replaces the corner trim/filler that covers panel edges or joins interior liners
• Helps keep adjoining panels, shelves or bins aligned and reduces gaps
• Restores appearance after chipping, cracks or impact damage

• Designed for drop-in or snap-on installation; verify fit against the appliance before final assembly
• Use basic hand tools; avoid excessive force which can crack plastic parts
• Disconnect power if removing interior panels or working near electrical components

Screw for control panel.

This replacement screw fastens panels, brackets, and internal components so they stay secure during operation. Replace worn, rusted, or missing screws to restore a solid fit and help reduce vibration, rattles, and misalignment.

• Secures appliance parts to maintain proper fit and alignment
• Helps reduce noise and vibration from loose panels or trim
• Replaces stripped, corroded, or missing fasteners
• Can resolve issues like rattling, gaps, or shifting components

• Disconnect power; turn off gas/water if applicable before servicing
• Match to the original screw and start threads by hand to avoid cross-threading
• Use the correct driver and tighten snugly; do not overtighten into plastic or thin sheet metal
• Replace additional worn fasteners in the same location if needed for even clamping

This 1/4-20 screw is a direct replacement fastener used to secure appliance panels, brackets, and assemblies. It restores proper fit and prevents rattling or loose components for safe, reliable operation. What it does:

• Fastens panels, mounting brackets, and components in place
• Replaces missing or stripped screws that cause loose or rattling parts
• Maintains alignment of assemblies to prevent wear and vibration
• Works wherever a 1/4-20 machine screw is specified by the manufacturer

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing
• Use the correct-size driver or socket to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or components
• If the original screw was rusted or seized, apply penetrating lubricant and use proper extraction tools

This base grill is the lower front trim piece that restores the look and airflow opening at the bottom of your refrigerator. It replaces a cracked, faded, or missing toe-kick panel to return a finished appearance. What it does:

• Covers and protects the refrigerator's lower front area while allowing required airflow beneath the cabinet.
• Replaces damaged, cracked, or broken grills and worn cosmetic trim.
• Secures to the cabinet with molded tabs or fasteners; helps keep debris out of the kickspace.
• Matches white finish for a clean, factory look.

• One white base grill (toe kick) as pictured.

• Usually fastens with snapped-in tabs or a few screws; align tabs and press until secure.
• No refrigerant handling required; shut off power only if recommended by your model's service instructions.
• Handle clips gently to avoid breakage; replace any damaged fasteners before final installation.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This wire harness routes power and control signals between the appliance control and components to restore reliable electrical connectivity. It replaces damaged or burned wiring to help resolve intermittent operation and loss of function. What it does:

• Provides organized, insulated wiring to connect the control board to heaters, motors, sensors and switches.
• Restores continuity where frayed, pinched or burned wires cause faults or shorts.
• Common symptoms this can address: control panel unresponsive, appliance won't start, intermittent power or components not operating.
• Designed to follow factory routing and connector positions for correct fit and electrical function.

• Disconnect all power before replacing any wiring; verify power is removed at the breaker or unplug the appliance.
• Take photos or mark connector positions before removal to ensure correct reconnection.
• Avoid pulling on individual wires; remove and install at the connector housings to prevent terminal damage.
• If wiring is severely corroded or connectors damaged, inspect adjoining components and replace per service manual.