Kenmore Refrigerator 106.51272201 (10651272201, 106 51272201) Parts

Fix uneven cooling and warm spots in your refrigerator with this air baffle. Directs cold air properly throughout compartments. Simple DIY fix.

Bearing body bracket for refrigerator assembly. Secures and supports internal components. Replace if cracked, broken, or damaged to restore proper fit.

Support plate kit for refrigerators. Includes left and right side mounting plates. Replace if cracked, broken, or missing to restore proper support.

Fix refrigerator electrical issues with this wire connector. Restores power to components when connections fail. Simple plug-in installation.

Wire tie secures and organizes internal wiring harnesses in your appliance. Replace if the original tie is broken, cracked, or missing during repairs.

Secures refrigerator shelves to the liner wall. Replace this stud if shelves sag, sit unevenly, or won't stay in place due to broken or missing support.

Cosmetic cover that attaches at the base of your refrigerator for a finished look. Replace if cracked, broken, or missing to restore appearance.

Covers the ice chute in your refrigerator's dispenser. Replace if the door is cracked, broken, missing clips, or won't stay closed properly.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Replacement oven trivet that supports cookware and broiler pans to keep them level during baking and broiling. Restores a stable cooking surface so pots and pans sit securely in the oven. What it does:

• Provides a stable support surface for cookware and broiler pans during baking and broiling.
• Helps prevent cookware from wobbling, tipping or sliding on the oven rack.
• Restores proper cookware clearance and positioning when the original trivet is bent, cracked or missing.
• Can reduce uneven cooking caused by unstable cookware placement.

• Disconnect power and allow the oven to fully cool before installing or handling the trivet.
• Install by placing the trivet into the original mounting location or slots; no special tools are normally required.
• Inspect mounting points or clips for damage and replace if needed to ensure a secure fit.

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

This thermostat knob is the control dial used to set temperature on compatible ranges and ovens, restoring a clear pointer and easy grip when the original knob is cracked, faded, or missing. It provides a simple, user-facing control for the appliance thermostat. What it does:

• Turns the thermostat control shaft to select cooking temperature settings.
• Replaces cracked, worn, broken, loose, or missing knobs that make temperature adjustments difficult.
• Restores a visible pointer/indicator for accurate temperature selection.
• Improves grip and tactile feedback for safer, easier temperature changes.

• Turn appliance controls OFF and cool before replacing the knob.
• Remove the old knob by pulling it straight off the control shaft; align the new knob splines with the shaft and push on until fully seated.
• If the knob is stuck, use gentle rocking while pulling; do not pry on surrounding surfaces or force the shaft.

Fix ice that won't crush or dispense with this refrigerator crusher blade. Solves bent or damaged blades preventing ice from dispensing. Easy DIY repair.