Kenmore Refrigerator 106.58272801 (10658272801, 106 58272801) Parts

This bearing nut secures a bearing and related rotating components on the shaft, keeping the assembly tight and aligned for smooth, dependable operation. Replacing a worn or stripped nut helps stop wobble, noise, and drive slippage.

• Locks the bearing/stack onto the shaft to prevent loosening
• Maintains alignment for smooth rotation and reduced vibration
• Helps restore consistent drive in shaft-driven assemblies
• Typical symptoms: loose or non-turning drive, rattling/grinding, or visible thread damage

• Disconnect power before servicing; shut off water if working near dispenser components
• Remove the related assembly to access the shaft; note part order for reassembly
• Hand-start the nut to avoid cross-threading; verify thread direction against the original
• Tighten securely; inspect the bearing, washers/spacers, and shaft for wear

Crisper drawer won't adjust humidity or slide is broken? This humidity control slide mounts in the crisper cover to regulate airflow and moisture levels.

Mounts in the dispenser to secure the ice housing assembly. Keeps the chute and door aligned for smooth dispensing. Replace if cracked, broken, or worn.

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

This chute channels water and wash additives from the dispenser housing into the tub. Replacing a damaged or clogged chute helps ensure proper dispensing and reduces leaks or residue around the dispenser area. What it does:

• Guides detergent/bleach/fabric softener from the dispenser to the wash tub
• Maintains proper flow to prevent backups at the dispenser drawer
• Helps reduce leaks and drips from the dispenser area
• Common failure symptoms include water backing up into the drawer, detergent residue left in the dispenser, or leaks at the front-left/top of the washer

• 1 chute

• Disconnect power and turn off water supply before servicing
• Access is typically from the top; remove panels as needed to reach the dispenser assembly
• Transfer any seals, clamps, or hardware from the old chute
• Reassemble and run a brief fill/rinse to check for proper flow and leaks

Replacement mounting screw secures panels, brackets, and trim to the appliance frame. Needed when original screw is stripped, missing, or damaged.

Replace a cracked or broken crisper vent housing that mounts to your refrigerator's crisper cover. Holds the slider track for humidity control adjustment.

Mounting screw secures panels, brackets, and trim on refrigerators and washers. Replace when fasteners are missing, loose, stripped, or damaged.

Screw: 8-16 x 3/8 inch.

Replace a bent, broken, or missing freezer wire shelf. Restores stable storage space for frozen foods. Slides onto support studs in the freezer compartment.

Covers the ice chute in your refrigerator's dispenser. Replace if the door is cracked, broken, missing clips, or won't stay closed properly.

Secures cabinet or door handle to your refrigerator. Replace this clip if your handle is loose, sagging, or detached from the door mounting point.

Bottom hinge plate anchors your refrigerator's lower door hinge. Replace when door sags, won't close properly, or plate shows wear. Verify fit by model.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Ice crusher not working or producing inconsistent crushed ice? This rotating crusher blade restores proper ice crushing when worn, bent, or cracked.

This 6-position switch assembly replaces a worn or damaged selector switch to restore reliable electrical switching for the appliance control. It helps recover proper cycle selection and responsive control inputs for normal operation. What it does:

• Routes power between control circuits so selected cycles and settings engage correctly.
• Restores reliable selector/position switching when the control won't change settings.
• Common symptom when failing: appliance is unresponsive to cycle changes, selections don't register, or operation is intermittent.
• Matches the OEM switch function used in the control/timer area of compatible units.

• Disconnect power to the appliance before beginning any service to avoid shock hazard.
• Remove required panels or the control console to access the switch; keep track of screw locations and wire connections.
• Photograph or label wiring before disconnecting to ensure correct reassembly.