Kenmore Refrigerator 106.58973700 (10658973700, 106 58973700) Parts

A slide-out wire shelf that restores storage and access in your refrigerator. The sturdy wire design helps organize items and lets you pull stored food forward for easier reach and visibility. What it does:

• Provides a durable, roll-out surface for storing deli, produce, and other items.
• Slides smoothly on built-in rails so contents are easier to access.
• Replaces bent, broken or missing shelves that cause items to tip or fall.
• Helps maximize usable refrigerator space and improve organization.

• Remove all items from the compartment and power off the appliance before starting.
• Slide the shelf onto the cabinet rails or brackets until it seats securely; confirm both sides are aligned.
• If rails or clips are damaged, replace those components before installing this shelf.
• Use care to avoid pinching fingers when seating the shelf.

Color: Biscuit

This is for the right hand side

This is a single OEM replacement screw used to secure panels and components on compatible appliances. It restores proper fit and prevents loose or vibrating parts for a safer, more reliable repair. What it does

• Secures panels, brackets, and small components in appliance assemblies
• Restores proper alignment and fit when original screw is missing or damaged
• Prevents rattling, vibration noise, and parts shifting during operation
• Works where the OEM specifies this exact screw size and thread

• One replacement screw

• Unplug the appliance or shut off power before servicing
• Use the matching driver and avoid over-tightening to prevent stripping threads
• Verify correct screw length and thread engagement for the mounting point
• If other fasteners appear worn or damaged, inspect and replace as needed

A roll pin (spring pin) that secures rotating or sliding components by fitting into matched holes to hold shafts, levers, or brackets in place. Replaces a worn or damaged pin to restore proper mechanical engagement. What it does:

• Holds shafts, levers or hinges in position by expanding into drilled holes for a snug, vibration-resistant fit
• Keeps pulleys, rollers, or linkages from moving out of alignment or sliding off their shafts
• Common symptom: loose or wobbling pulley, lever, or shaft where the retaining pin is worn or broken
• Common symptom: noisy or intermittent operation caused by a pin that no longer secures moving parts

• Inspect mating holes and shaft for wear; replace pin with correct size to ensure secure fit
• Use appropriate pliers or a pin punch and hammer to drive the pin in or out; support the assembly to avoid damage
• Wear eye protection when installing or removing roll pins—pins can snap or fly out under force
• If pin is difficult to remove or install, consider using penetrating oil or heating only per OEM guidance

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This replacement dispenser lever restores proper operation to a refrigerator water dispenser so you can reliably access water without using a damaged or worn lever. Fits the dispenser assembly and provides a stable push surface. What it does

• Replaces a cracked, loose, or broken water dispenser lever so the dispenser paddle responds correctly.
• Helps stop sticking or uneven travel that prevents the valve from activating.
• Restores proper alignment with the dispenser bezel and actuator for consistent operation.
• Suitable when the lever is worn, chipped, or no longer returns smoothly.

• One dispenser lever

• Basic hand tools typically required; avoid forcing plastic tabs to prevent breakage.
• Disconnect power to the appliance and turn off the water supply before replacing parts that interact with the dispenser valve.
• Handle the new lever carefully to avoid damaging mounting clips; test function gently after installation.

This is a replacement mounting screw used to secure appliance panels and small components. It provides a correct-fit fastener to restore secure attachment and eliminate rattles or loose parts. What it does:

• Secures trim, panels, brackets, or small assemblies to prevent movement and vibration
• Restores proper alignment when a worn or missing screw causes loose parts or noise
• Works as a direct-replacement fastener where the OEM screw specification is required

• One replacement screw

• Use the correct driver bit to avoid stripping the head; do not overtighten
• Disconnect power and follow appliance safety guidelines when accessing internal components
• If the original mounting hole or threads are damaged, repair or replace the mounting hardware before reinstalling

This for the left hand side