Kenmore Refrigerator 106.69728901 (10669728901, 106 69728901) Parts

This compressor start device energizes the refrigerator compressor's start winding to begin the cooling cycle, then disengages it. Replacing a weak or failed start device can restore reliable starts and address repeated clicking and warm/no-cool symptoms.

• Provides initial power to the compressor's start winding for reliable startup
• Disengages the start circuit once the compressor is running
• Common failure symptoms: compressor won't start, frequent clicking from the rear, refrigerator or freezer not cooling
• Heat damage or burnt odor on the old device may be present when it fails

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove the rear access panel to reach the compressor compartment
• Note wire positions; if your model uses a separate run capacitor, transfer it; move wires to the new device one at a time
• Align the device with the compressor terminals and press straight on until fully seated; reinstall any cover or retainer

This meat pan holder is the under-shelf support that guides the deli/meat drawer. Replacing a cracked holder restores smooth sliding and keeps the pan level so it doesn't bind, sag, or drop when opening and closing. What it does:

• Supports and guides the deli/meat pan beneath its shelf
• Keeps the drawer aligned and level for smooth operation
• Helps prevent rubbing, sticking, or the drawer falling off its track
• Typical failure signs: cracked plastic, broken mounting tabs, pan tilts or won't slide smoothly

• 1 meat pan holder

• Disconnect power and clear the shelf area for safe access
• Remove the meat pan and the shelf it rides on
• Release the damaged holder and install the new holder in the same orientation and mounting points
• Reinstall the shelf and drawer; verify smooth travel before loading

Size: 8 x 1-1/4 inch.

Color: White. Size: 2 oz. can. Porcelain touch-up paint.

This bottom hinge shim installs at the refrigerator's lower door hinge to fine-tune door height and alignment. Replacing a worn or missing shim can help restore smooth closing and an even, reliable gasket seal.

• Spaces the door at the lower hinge to set proper height and alignment
• Helps reduce door sagging or rubbing against the cabinet or other door
• Can help the door gasket seal evenly to minimize warm-air leaks

• Disconnect power and, if applicable, shut off the water supply
• Remove items from the door and support the door to prevent strain
• Loosen/remove lower hinge hardware and place the shim in the original location/orientation
• Reassemble, check alignment, and verify even gasket contact around the door

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This factory screw secures panels, brackets, and internal components in your appliance. Replacing a missing, stripped, or corroded fastener restores a snug fit, reduces vibration and noise, and helps keep assemblies aligned for reliable operation.

• Fastens components to maintain proper alignment and structural support
• Replaces a missing, damaged, or stripped screw
• Helps reduce rattling, vibration, or looseness
• Restores secure mounting of covers, trim, and assemblies

• Disconnect power; turn off gas or water supplies as applicable before servicing.
• Compare to the original to match length and thread.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• Reinstall any brackets or trim in the original order and orientation.

Color: White

This clip kit secures small panels, wiring harnesses, or trim on compatible Whirlpool appliances to prevent rattling and keep components in their intended position. It restores proper fit and helps reduce noise from loose parts. What it does:

• Holds wiring harnesses and cables in place to prevent chafing or contact with moving parts
• Secures panels, trim, or hoses so assemblies stay aligned and quiet
• Reduces rattling, buzzing, or vibration caused by loose components
• Keeps parts positioned during normal use and transport

• Disconnect power (unplug or shut off breaker) before starting any repair
• Use basic hand tools; avoid forcing clips into place to prevent breakage
• Replace any damaged clips with the exact kit to ensure proper fit
• Re-check that fastened parts are secure and that there are no pinched wires before restoring power

The Leveling Leg is an OEM part for Whirlpool refrigerators. This adjustable leg ensures your refrigerator is level. A level refrigerator ensures that doors seal properly, minimizing energy consumption and preventing uneven cooling or frost buildup. 

Causes of damage to the leveling leg can range from normal wear and tear, corrosion from moisture exposure, or physical damage during moving or cleaning processes. It's also possible for the leg to become stiff or seized, making adjustment difficult.

Symptoms of a bad Leveling Leg include:

• The refrigerator wobbles or is unstable when doors are opened or closed.
• Difficulty in aligning the refrigerator doors due to the appliance not being level.
• Increased operational noise or vibrations, especially when the compressor turns on, indicating the refrigerator is not sitting evenly.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement cab roller restores smooth movement and support for the appliance cabinet/door component, helping reduce noise and prevent binding from worn or damaged rollers. What it does

• Supports and guides the cabinet/door or sliding assembly for proper alignment
• Helps maintain smooth, quiet operation during opening/closing or movement
• Worn or broken rollers can cause sticking, scraping, or unusual noise
• Replacing the roller resolves common movement and alignment symptoms

• One roller

• Disconnect power and water before starting any repair
• Remove the affected panel or door per the appliance service instructions to access the roller
• Inspect mounting bracket and tracks for wear or damage; replace additional damaged parts as needed
• Use basic hand tools; avoid forcing components to prevent damage

Color: Black

This OEM grease is a purpose-made appliance lubricant that reduces friction and protects moving parts for smoother operation and longer component life. Use where specified by the manufacturer for bearings, slides, or motor shafts. What it does:

• Lubricates gears, bearings, rollers and shafts to reduce wear and noise
• Helps prevent binding, seizing, and grinding on moving components
• Protects metal parts from corrosion where grease is specified
• Keeps parts moving smoothly under normal operating temperatures

• Disconnect power before servicing any appliance; follow manufacturer service instructions
• Apply sparingly to clean, dry surfaces; avoid over-greasing which can attract debris
• Wear gloves and wipe excess grease from surrounding areas to prevent staining

Sealer for refrigerant line insulation.

Color: white.