Kenmore Refrigerator 106.69729900 (10669729900, 106 69729900) Parts

This mechanical thermostat monitors temperature and opens or closes the circuit at a fixed set point to control heat and prevent overheating. Replacing a failed thermostat restores safe operation and consistent performance. What it does:

• Senses surface or component temperature and switches the circuit at a calibrated threshold
• Helps protect heaters, motors, and controls from thermal damage due to over-temperature
• Common symptoms of failure: no heat, shuts off mid-cycle, won't start until cooled, or intermittent operation
• Restores proper temperature control after a thermostat sticks open/closed or drifts out of spec

• 1 thermostat

• Disconnect power at the breaker (and shut off gas, if applicable) before servicing
• Note wire positions and transfer leads one-for-one to the new thermostat
• Mount flush against the sensing surface with original screws/clips; reinstall any insulation or thermal interface material as found
• Correct the root cause (blocked vents, failed fan, restricted airflow, or buildup) before returning the appliance to service

This humidity control slide mounts on the crisper cover and moves the vent door that regulates moisture in the produce bin. Replacing a broken slider restores smooth adjustment so you can fine-tune humidity for better food freshness.

• Moves the crisper vent door between high and low humidity settings to control airflow
• Restores smooth, positive slider action and clear setting selection
• Common symptoms: slider cracked, missing, or stuck; humidity setting won't hold; crisper too wet or too dry; condensation in the drawer
• Direct-fit replacement for the original crisper humidity vent slider

• Unplug the refrigerator and remove the crisper drawer(s) for access
• Lift out or access the crisper cover where the slider seats
• Align the new slide with the vent/damper lever and snap or slide it into place
• Confirm smooth travel through the full range before reinstalling the drawer(s)

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This top door hinge is the butt hinge assembly that mounts to the cabinet at the top of the refrigerator door, supporting the door and allowing smooth swing. Replacing a worn hinge restores alignment and a reliable seal.

• Provides the upper pivot point for the door
• Keeps the door aligned so the gasket seals correctly
• Wear or damage can cause sagging, rubbing, squeaks, or a door that won't close fully
• Helps reduce air leaks and temperature swings near the door

• Disconnect power and remove items from the door to reduce weight
• Support the door from below; remove the hinge cover and mounting screws
• Note the position of any shims/spacers and transfer them to the new hinge
• Reinstall, align the door, tighten screws, and ensure proper gasket contact

This is the center hinge for the refrigerator doors. It supports and aligns the doors at the midpoint so they open smoothly and seal properly, helping maintain temperatures and reliable day-to-day operation.

• Provides the middle pivot point between the upper and lower doors
• Keeps door alignment and spacing correct for a tight gasket seal
• Common symptoms: door sagging or rubbing, squeaking/grinding, door not closing or popping open, uneven gaps
• Replace if the hinge bracket or pin is bent, worn, or corroded

• Disconnect power and clear items from the doors before starting
• Support the doors; a second person is recommended when removing hinge screws
• Note the order of any shims/spacers or washers and transfer them to the new hinge
• After installation, align doors and verify full gasket contact all around

This rubber grommet cushions and secures a refrigerator fan motor, isolating vibration to help reduce noise and keep the fan properly aligned in its mount.

• Provides a snug, vibration-dampening seat for the fan motor shaft or mounting stud
• Helps prevent rattling, buzzing, or humming sounds from a loose fan mount
• Maintains proper fan alignment to avoid blade contact with shrouds or brackets
• Replaces aged, cracked, or compressed rubber that can lead to increased vibration

• Disconnect power before service; wear cut-resistant gloves
• Access the fan assembly (rear or evaporator section), support the motor, and remove the old grommet
• Press the new grommet fully into the bracket or housing; transfer any spacers as originally configured
• Reinstall the motor and verify the fan blade spins freely with no contact before restoring power

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does

• Forms a reliable seal between components to prevent fluid or air leaks
• Maintains proper operation by keeping the sealed area contained
• Replaces gaskets that are brittle, cracked, flattened, or swollen
• Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal

• 1 gasket/seal

• Disconnect power and any water or gas supply before servicing
• Note the gasket's orientation; compare old and new parts before installation
• Clean and dry mating surfaces; remove old adhesive and debris
• Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly

Due to manufacturer changes, if D shaft hinge pin is needed use part number WP2325483.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This replacement freezer shelf restores a sturdy, level storage surface in the freezer compartment, helping you organize frozen foods and make full use of available space. What it does:

• Provides a solid, level surface to support food packages in the freezer
• Helps organize items and maximize vertical storage capacity
• Replace if the shelf is bent, broken, unstable, corroded, or missing
• Symptoms include sagging or uneven shelf, items tipping, and reduced usable space

• Unplug the refrigerator before servicing
• Remove items from the freezer; lift or disengage the old shelf from its supports
• Align the new shelf with side supports or mounting holes and seat it fully so it's level and secure
• Distribute weight evenly and avoid overloading after installation

Color: white. It measures about 1 inch in diameter.

Size: 8-18 x 1/2 inch.

This meat pan holder is the under-shelf support that guides the deli/meat drawer. Replacing a cracked holder restores smooth sliding and keeps the pan level so it doesn't bind, sag, or drop when opening and closing. What it does:

• Supports and guides the deli/meat pan beneath its shelf
• Keeps the drawer aligned and level for smooth operation
• Helps prevent rubbing, sticking, or the drawer falling off its track
• Typical failure signs: cracked plastic, broken mounting tabs, pan tilts or won't slide smoothly

• 1 meat pan holder

• Disconnect power and clear the shelf area for safe access
• Remove the meat pan and the shelf it rides on
• Release the damaged holder and install the new holder in the same orientation and mounting points
• Reinstall the shelf and drawer; verify smooth travel before loading

Size: 8 x 1-1/4 inch.