Kenmore Refrigerator 106.70104000 (10670104000, 106 70104000) Parts

This refrigerator compressor circulates refrigerant to cool the appliance and restore proper temperatures. Replaces a failed compressor to help the refrigerator maintain set temperatures when the cooling system is compromised. What it does:

• Pumps refrigerant through the sealed cooling system to enable heat exchange and cooling.
• Runs the refrigeration cycle so the refrigerator and freezer can reach and hold target temperatures.
• Common symptom linkage: fridge not cooling, compressor humming or not running, or frequent cycling.
• Can cause system pressure issues if damaged or leaking.

• One compressor (single sealed unit)

• Power should be disconnected before beginning work and the refrigerant must be recovered per regulations.
• System evacuation, leak testing, and proper recharge with the correct refrigerant are necessary after replacement.
• May require replacement of mounting hardware, start device, or filter-drier—verify system condition during service.

Color: White.

This OEM grease is a purpose-made appliance lubricant that reduces friction and protects moving parts for smoother operation and longer component life. Use where specified by the manufacturer for bearings, slides, or motor shafts. What it does:

• Lubricates gears, bearings, rollers and shafts to reduce wear and noise
• Helps prevent binding, seizing, and grinding on moving components
• Protects metal parts from corrosion where grease is specified
• Keeps parts moving smoothly under normal operating temperatures

• Disconnect power before servicing any appliance; follow manufacturer service instructions
• Apply sparingly to clean, dry surfaces; avoid over-greasing which can attract debris
• Wear gloves and wipe excess grease from surrounding areas to prevent staining

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

Sealer for refrigerant line insulation.

Color: white.

This hole plug covers the screw access on appliance handles for a finished, factory appearance. It helps keep moisture and debris out of the handle cavity while restoring a clean, matching look to the door. What it does:

• Covers exposed handle screw holes for a finished appearance
• Helps prevent moisture, dirt, and food particles from entering the handle cavity
• Restores a color-matched cosmetic finish to the handle area
• Useful when replacing a handle or finishing a repair where the plug is missing

• One biscuit-colored handle hole plug

• Push the plug into the hole until it snaps flush; may require light pressure or a soft mallet
• Remove the old plug by prying gently with a plastic trim tool to avoid scratching the finish
• No electrical disconnection is typically required for this cosmetic part; follow appliance manufacturer guidance for any door/handle work

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 3/16 inch.

Size: 5/16 inch.

Size: 3/8 inch.

Size: 3/4 inch.

This hole plug covers and protects unused mounting or access holes on the appliance cabinet or trim, giving a finished appearance and preventing dirt or moisture from entering. It's a simple cosmetic and protective replacement. What it does:

• Covers exposed holes in panels, trim, or end caps to improve appearance
• Helps keep out dirt, moisture and small debris from unused openings
• Restores a clean, finished edge after part removal or repair
• Commonly used where a small plastic plug is pressed into a hole for a flush fit

• One hole plug

• Press into the opening until flush; no tools required for most installations
• Ensure the hole is clean and dry before installing for best fit
• Replace only with the correct size plug to avoid loose fit or damage
• Disconnect power and follow appliance safety guidelines if working near electrical components

Size: 1/4 lb.