Kenmore Refrigerator 106.70234904 (10670234904, 106 70234904) Parts

Secures the compressor to the refrigerator frame. Replace if strap is cracked, broken, or missing to properly mount and stabilize the compressor unit.

Replacement mounting screw for securing panels, brackets, and components in appliances. Needed when original fastener is missing, stripped, or damaged.

This insulation bag fits inside the refrigerator or freezer door panel to help maintain consistent internal temperatures. It acts as a thermal barrier that prevents warm outside air from affecting the sealed compartment. Replace it if you notice condensation forming on the door interior, inconsistent temperatures, or if the existing insulation is torn, compressed, or missing.

Ice maker not producing ice or working intermittently? This wiring harness restores electrical connections to power ice production. DIY-friendly repair.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This trim tail handle restores the finished edge and secure mounting at the end of a door or trim panel, improving appearance and helping keep the panel seated correctly. Fits where the trim meets the appliance body. What it does:

• Covers and finishes the exposed end of a trim or door panel for a clean, factory look
• Helps hold the trim/door edge in position to reduce rattling or looseness
• Restores proper fit and alignment after damage or wear to the original trim
• Simple replacement that addresses cosmetic defects and loose or misaligned trim

• Disconnect power or unplug the appliance before starting work
• Use basic hand tools; support the door/panel to prevent drops or pinching
• Keep track of fasteners and use the original screws where applicable

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

Trim piece that covers and finishes the outer corner where filler panels meet on your refrigerator. Replace if cracked, broken, or missing.

Replaces cracked, loose, or missing door shelf trim on your refrigerator. Restores the finished edge and support for door shelves to keep items secure.

Replacement mounting screw for refrigerators. Secures panels, trim pieces, and small assemblies. Needed when original screw is missing or damaged.

Secures internal components in your refrigerator to keep parts stable and prevent rattling. Replace if bent, broken, or missing to restore alignment.

Replaces the plastic front edge trim on refrigerator door shelves. Needed when the original trim is cracked, chipped, broken, or missing from your shelf.

Fix ice maker or water dispenser issues with this valve tube body. Routes water from the main valve to dispenser and ice maker. Stops leaks from damaged tubes.

This is a replacement 1/4-20 threaded screw used to secure appliance components and panels. It restores proper fastening where a matching screw is missing, loose, or stripped and helps stop rattling or misalignment. What it does:

• Secures panels, brackets, and assemblies to maintain proper alignment and reduce vibration
• Replaces missing or damaged fasteners that cause loose or rattling parts
• Works wherever a 1/4-20 threaded screw is specified by the manufacturer
• Simple mechanical fastener—no electrical or calibration changes required

• Disconnect power to the appliance before servicing to avoid injury
• Use the matching driver and thread engagement; do not overtighten to prevent stripping
• Verify screw length and head type match the original before installing
• If threads are damaged, repair or replace the mating component rather than forcing the screw