Kenmore Refrigerator 106.8552610 (1068552610, 106 8552610) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10250570
This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:
- Supports the refrigerator cabinet and helps maintain proper leveling
- Allows the unit to roll for easier cleaning and servicing
- Replaces worn, cracked, or seized rollers and damaged brackets
- Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge
What's included:
- One complete cabinet roller assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
- Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
- After installation, level the refrigerator and verify doors close and seal properly
Do-It-Yourself Stories from Customers like You
The plastic left rear wheel was coming apart and needed replacing Gary H. • San Antonio , TX • June 11, 2016
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The...
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 2188404A
The Refrigerator Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.
Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door.
Symptoms of a bad refrigerator door gasket include:
- Warm air entering the refrigerator, causing it to run more frequently
- Condensation or frost buildup inside the refrigerator
- Difficulty keeping the door closed
- Visible cracks, tears, or deformation in the gasket
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Condensation was forming along the top interior of refrigerator Susan H. • Springfield , NJ • September 10, 2014
I called Appliance Parts Pros and gave them the model number of my refrigerator. They promptly advised me exactly what part I needed, told me the price and cost of shipping. I agreed and received my part within 2 days.
I watched the video that told me exactly how to complete repair. It was very simple. The only thing different was that there was a metal strip holding the gasket in place. Removing it was no problem. When I installed it I had to loosen the screws? nuts? slip the gasket...
Read more
More
$135.43
- Compare At:
-
$162.52
- You Save:
-
$27.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP1106508
This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does
- Forms a reliable seal between components to prevent fluid or air leaks
- Maintains proper operation by keeping the sealed area contained
- Replaces gaskets that are brittle, cracked, flattened, or swollen
- Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal
What's included
Install notes
- Disconnect power and any water or gas supply before servicing
- Note the gasket's orientation; compare old and new parts before installation
- Clean and dry mating surfaces; remove old adhesive and debris
- Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly
Do-It-Yourself Stories from Customers like You
Delivery person broke fitting off for the ice maker while removeing our "good" old fridge that was already sold Donald J. • Fremont , MI • October 13, 2014
I ordered the repair parts that Lowes said they couldn't get. I got the parts very fast and only took 5 minutes to get the job done.
Read more
More
$6.42
- Compare At:
-
$7.58
- You Save:
-
$1.16
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387491
These inserts are for 1/4 inch plastic tubing. Package of 4.
More
$11.95
- Compare At:
-
$13.22
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400906
This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.
- Fastens brackets, panels, ducts, or housings to the cabinet or frame
- Replaces missing, stripped, or corroded hardware
- Helps stop rattles, vibration, and loose or misaligned parts
- Maintains proper alignment for reliable operation
Includes: 1 screw
- Disconnect power; shut off gas and water before servicing
- Match this screw to the original location and hardware type used on your model
- Start threads by hand to avoid cross-threading; use the correct driver
- Snug only—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Broken ice maker door and tabs David G. • San Antonio , TX • December 22, 2018
Through your website and YouTube DIY’s I was able to find the parts for my specific refrigerator and fix it, the wife had been after me for over a year to fix it and did not. I was ready to buy a new refrigerator but decided to try and fix it myself you guys rock !
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2182124
Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:
- Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
- Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
- Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
- A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.
What's included: One ice stripper. Install notes:
- Disconnect power to the appliance before starting any repair to avoid electrical shock.
- Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
- Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
- After installation, restore power and run a test harvest cycle to ensure proper cube ejection.
Do-It-Yourself Stories from Customers like You
Ice stripper was broken on ice maker John A. • Baton Rouge , LA • March 12, 2015
Checked out the video on your site on how to disassemble the ice maker. Was really easy when you know the correct sequence. Only 3 screws and it's out of the freezer. Disassembled the ice maker on my kitchen counter and replaced the ice stripper. Reassembled and installed back in my freezer. It is as good as new
Read more
More
$47.95
- Compare At:
-
$57.06
- You Save:
-
$9.11
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2262181
This PTC start relay mounts on the compressor and momentarily powers the start winding to get the motor running, then disengages for normal operation. Replacing a weak relay can stop repeated clicking and help restore cooling.
- Provides initial boost to the compressor's start winding for reliable startup
- Automatically drops out after startup so the compressor runs on the run winding
- Helps address symptoms like warm temperatures, compressor clicking or humming without starting, or frequent overload trips
- Failure may show as rattling, burn marks, or a melted relay housing
What's included: 1 PTC start relay Install notes:
- Disconnect power and remove the rear access panel to reach the compressor
- Allow components to cool; note wire locations and take a reference photo
- Pull the old relay straight off the compressor pins; align and firmly seat the new relay in the same orientation, then reconnect wires
- If your unit uses a run capacitor and/or separate overload protector, reconnect per the wiring diagram before restoring power
Do-It-Yourself Stories from Customers like You
Refrigerator stopped cooling compressor was warm heard clicking Gale W. • Wimberley , TX • November 21, 2014
Googled the symptoms. Found the part. Watched a How To movie on YouTube. Bought the part installed the part. My wife thinks I'm a genius.
Read more
More
$64.60
- Compare At:
-
$77.52
- You Save:
-
$12.92
Genuine Whirlpool part
By: Whirlpool
Part Number: W10749708
This coupling is the small connector that links a drive motor to its mating component, transferring rotation so the appliance operates smoothly. Replacing a cracked or stripped coupling restores reliable drive and helps prevent further wear.
- Connects the motor shaft to the driven part to transmit torque
- Maintains alignment to reduce wobble and slippage
- Failure signs can include no movement, intermittent operation, clicking/grinding, or visible cracks/rounding
- Restores consistent motion of the connected part once replaced
What's included: 1 coupling Install notes:
- Disconnect power (and shut off water/gas if applicable) before servicing
- Access the drive area and remove any covers/tray/drive components as needed
- Pull the old coupling straight off the keyed or D-shaped shaft; clean and inspect the shaft
- Align and press the new coupling fully onto the shaft, reassemble, and test
Do-It-Yourself Stories from Customers like You
Icemaker self destructed after 12 hr power failure following a storm ice melted particially down and jammed auger Walt P. • Maypearl , TX • May 02, 2015
Required new ice bin (container) which has busted up in pieces from the stress of trying to turn while half melted ice had it jammed, something had to give. Ice auger ripped itself out of the dispenser end breaking the ice container. Got new container, disassembled per the drawing, reassembled.
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP1120581
An ice maker delay mechanism is the small timing device that staggers the steps of the ice-making cycle so each action happens in the right order. Replacing a worn unit helps restore steady, predictable ice production.
- Provides a brief, controlled delay in the ice maker cycle so components engage in the correct order
- Helps prevent short cycling or erratic operation
- Failure may result in no ice, intermittent ice, or stalls mid-cycle
- May be accompanied by repeated clicking or ticking from the ice maker head
What's included: Includes 1 delay mechanism. Install notes:
- Disconnect power to the refrigerator and shut off the water supply before servicing
- Remove the ice maker assembly to access the delay mechanism
- Transfer any brackets or clips from the original part if required
- Align components carefully during reassembly to avoid bending any lever arms
Do-It-Yourself Stories from Customers like You
Water tube assembly. William R. • Tyler , TX • August 02, 2023
Used the parts ordered from AppliancePartsPros.com, along with Youtube video from AppliancePartsPros.com to replace the water tube assembly. Suggestions made in that video made the difference in making the repair or not making the repair.
Read more
More
$96.45
- Compare At:
-
$114.40
- You Save:
-
$17.95